Fujifilm FinePix SL300 vs. Fujifilm FinePix S4300

Comparison

change cameras »
FinePix SL300 image
vs
FinePix S4300 image
Fujifilm FinePix SL300 Fujifilm FinePix S4300
check price » check price »
Megapixels
14.00
14.00
Max. image resolution
4288 x 3216
4288 x 3216

Sensor

Sensor type
CCD
n/a
Sensor size
1/2.3" (~ 6.16 x 4.62 mm)
1/2.3" (~ 6.16 x 4.62 mm)
Sensor resolution
4315 x 3244
4315 x 3244
Diagonal
7.70 mm
7.70 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1 : 1
(ratio)
Fujifilm FinePix SL300 Fujifilm FinePix S4300
Surface area:
28.46 mm² vs 28.46 mm²
Difference: 0 mm² (0%)
SL300 and S4300 sensors are the same size.
Pixel pitch
1.43 µm
1.43 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 0 µm (0%)
SL300 and S4300 have the same pixel pitch.
Pixel area
2.04 µm²
2.04 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 0 µm² (0%)
Fujifilm SL300 and Fujifilm S4300 have the same pixel area.
Pixel density
49.07 MP/cm²
49.07 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 0 µm (0%)
Fujifilm SL300 and Fujifilm S4300 have the same pixel density.
To learn about the accuracy of these numbers, click here.



Specs

Fujifilm SL300
Fujifilm S4300
Crop factor
5.62
5.62
Total megapixels
Effective megapixels
14.00
Optical zoom
30x
Digital zoom
Yes
ISO sensitivity
Auto, 64, 100, 200, 300, 400, 800, 1600, (3200, 6400 with boost)
RAW
Manual focus
Normal focus range
40 cm
Macro focus range
2 cm
Focal length (35mm equiv.)
24 - 720 mm
Aperture priority
Yes
Max. aperture
f3.1 - f5.9
Max. aperture (35mm equiv.)
f17.4 - f33.2
n/a
Metering
Multi, Center-weighted, Spot
Exposure compensation
±2 EV (in 1/3 EV steps)
Shutter priority
Yes
Min. shutter speed
8 sec
Max. shutter speed
1/2000 sec
Built-in flash
External flash
Viewfinder
Electronic
Electronic
White balance presets
6
Screen size
3"
Screen resolution
460,000 dots
Video capture
Max. video resolution
Storage types
SD/SDHC/SDXC
USB
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
Lithium-ion NP-85 rechargeable battery
Weight
510 g
Dimensions
122 x 93 x 100 mm
Year
2012
2012




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Fujifilm SL300 diagonal

The diagonal of SL300 sensor is not 1/2.3 or 0.43" (11 mm) as you might expect, but approximately two thirds of that value - 7.7 mm. If you want to know why, see sensor sizes.

w = 6.16 mm
h = 4.62 mm
Diagonal =  6.16² + 4.62²   = 7.70 mm

Fujifilm S4300 diagonal

The diagonal of S4300 sensor is not 1/2.3 or 0.43" (11 mm) as you might expect, but approximately two thirds of that value - 7.7 mm. If you want to know why, see sensor sizes.

w = 6.16 mm
h = 4.62 mm
Diagonal =  6.16² + 4.62²   = 7.70 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

SL300 sensor area

Width = 6.16 mm
Height = 4.62 mm

Surface area = 6.16 × 4.62 = 28.46 mm²

S4300 sensor area

Width = 6.16 mm
Height = 4.62 mm

Surface area = 6.16 × 4.62 = 28.46 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

SL300 pixel pitch

Sensor width = 6.16 mm
Sensor resolution width = 4315 pixels
Pixel pitch =   6.16  × 1000  = 1.43 µm
4315

S4300 pixel pitch

Sensor width = 6.16 mm
Sensor resolution width = 4315 pixels
Pixel pitch =   6.16  × 1000  = 1.43 µm
4315


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

SL300 pixel area

Pixel pitch = 1.43 µm

Pixel area = 1.43² = 2.04 µm²

S4300 pixel area

Pixel pitch = 1.43 µm

Pixel area = 1.43² = 2.04 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

SL300 pixel density

Sensor resolution width = 4315 pixels
Sensor width = 0.616 cm

Pixel density = (4315 / 0.616)² / 1000000 = 49.07 MP/cm²

S4300 pixel density

Sensor resolution width = 4315 pixels
Sensor width = 0.616 cm

Pixel density = (4315 / 0.616)² / 1000000 = 49.07 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

SL300 sensor resolution

Sensor width = 6.16 mm
Sensor height = 4.62 mm
Effective megapixels = 14.00
r = 6.16/4.62 = 1.33
X =  14.00 × 1000000  = 3244
1.33
Resolution horizontal: X × r = 3244 × 1.33 = 4315
Resolution vertical: X = 3244

Sensor resolution = 4315 x 3244

S4300 sensor resolution

Sensor width = 6.16 mm
Sensor height = 4.62 mm
Effective megapixels = 14.00
r = 6.16/4.62 = 1.33
X =  14.00 × 1000000  = 3244
1.33
Resolution horizontal: X × r = 3244 × 1.33 = 4315
Resolution vertical: X = 3244

Sensor resolution = 4315 x 3244


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


SL300 crop factor

Sensor diagonal in mm = 7.70 mm
Crop factor =   43.27  = 5.62
7.70

S4300 crop factor

Sensor diagonal in mm = 7.70 mm
Crop factor =   43.27  = 5.62
7.70

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

SL300 equivalent aperture

Crop factor = 5.62
Aperture = f3.1 - f5.9

35-mm equivalent aperture = (f3.1 - f5.9) × 5.62 = f17.4 - f33.2

S4300 equivalent aperture

Aperture is a lens characteristic, so it's calculated only for fixed lens cameras. If you want to know the equivalent aperture for Fujifilm S4300, take the aperture of the lens you're using and multiply it with crop factor.

Crop factor for Fujifilm S4300 is 5.62

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.