Panasonic Lumix DMC-LC1 vs. Panasonic Lumix DMC-GF3
Comparison
change cameras » | |||||
|
vs |
|
|||
Panasonic Lumix DMC-LC1 | Panasonic Lumix DMC-GF3 | ||||
check price » | check price » |
Megapixels
4.90
12.10
Max. image resolution
2560 x 1920
4000 x 3000
Sensor
Sensor type
CCD
CMOS
Sensor size
2/3" (~ 8.8 x 6.6 mm)
Four Thirds (17.3 x 13 mm)
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera.
Sensors can vary greatly in size. As a general rule, the bigger the
sensor, the better the image quality.
Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.
Learn more about sensor sizes »
Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.
Learn more about sensor sizes »
Actual sensor size
Note: Actual size is set to screen → change »
|
vs |
|
1 | : | 3.87 |
(ratio) | ||
Panasonic Lumix DMC-LC1 | Panasonic Lumix DMC-GF3 |
Surface area:
58.08 mm² | vs | 224.90 mm² |
Difference: 166.82 mm² (287%)
GF3 sensor is approx. 3.87x bigger than LC1 sensor.
Note: You are comparing sensors of very different generations.
There is a gap of 7 years between Panasonic LC1 (2004) and Panasonic GF3 (2011).
Seven years is a lot of time in terms
of technology, meaning newer sensors are overall much more
efficient than the older ones.
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.
The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Pixel or photosite area affects how much light per pixel can be gathered.
The larger it is the more light can be collected by a single pixel.
Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 6.68 µm² (56%)
A pixel on Panasonic GF3 sensor is approx. 56% bigger than a pixel on Panasonic LC1.
Pixel density tells you how many million pixels fit or would fit in one
square cm of the sensor.
Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Higher pixel density means smaller pixels and lower pixel density means larger pixels.
To learn about the accuracy of these numbers,
click here.
Specs
Panasonic LC1
Panasonic GF3
Total megapixels
5.20
13.10
Effective megapixels
4.90
12.10
Optical zoom
3.2x
Digital zoom
Yes
Yes
ISO sensitivity
100, 200, 400
Auto, 160 - 6400
RAW
Manual focus
Normal focus range
60 cm
Macro focus range
30 cm
Focal length (35mm equiv.)
28 - 90 mm
Aperture priority
Yes
Yes
Max. aperture
f2.0 - f2.4
Metering
Centre weighted, Matrix, Spot
Centre weighted, Multi-segment, Spot
Exposure compensation
±2 EV (in 1/3 EV steps)
±3 EV (in 1/3 EV steps)
Shutter priority
Yes
Yes
Min. shutter speed
8 sec
60 sec
Max. shutter speed
1/4000 sec
1/4000 sec
Built-in flash
External flash
Viewfinder
Electronic
None
White balance presets
7
5
Screen size
2.5"
3"
Screen resolution
211,000 dots
460,000 dots
Video capture
Max. video resolution
Storage types
MultiMedia, Secure Digital
SDHC, SDXC, Secure Digital
USB
USB 2.0 (480 Mbit/sec)
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
Lithium-Ion 1400 mAh supplied
Lithium-Ion rechargeable battery
Weight
702 g
264 g
Dimensions
135 x 82 x 102 mm
107.7 x 67.1 x 32.5 mm
Year
2004
2011
Choose cameras to compare
Popular comparisons:
- Panasonic Lumix DMC-LC1 vs. Leica Digilux 2
- Panasonic Lumix DMC-LC1 vs. Panasonic Lumix DMC-LX100
- Panasonic Lumix DMC-LC1 vs. Panasonic Lumix DMC-LX7
- Panasonic Lumix DMC-LC1 vs. Fujifilm X-E1
- Panasonic Lumix DMC-LC1 vs. Fujifilm X10
- Panasonic Lumix DMC-LC1 vs. Panasonic Lumix DMC-LC5
- Panasonic Lumix DMC-LC1 vs. Panasonic Lumix DMC-FZ20
- Panasonic Lumix DMC-LC1 vs. Fujifilm FinePix X100
- Panasonic Lumix DMC-LC1 vs. Panasonic Lumix DMC-LX3
- Panasonic Lumix DMC-LC1 vs. Panasonic Lumix DMC-LX5
- Panasonic Lumix DMC-LC1 vs. Olympus E-410 / EVOLT E-410
Diagonal
Diagonal is calculated by the use of Pythagorean theorem:
where w = sensor width and h = sensor height
Diagonal = √ | w² + h² |
Panasonic LC1 diagonal
The diagonal of LC1 sensor is not 2/3 or 0.67" (16.9 mm) as you might expect, but approximately two thirds of
that value - 11 mm. If you want to know why, see
sensor sizes.
w = 8.80 mm
h = 6.60 mm
w = 8.80 mm
h = 6.60 mm
Diagonal = √ | 8.80² + 6.60² | = 11.00 mm |
Panasonic GF3 diagonal
w = 17.30 mm
h = 13.00 mm
h = 13.00 mm
Diagonal = √ | 17.30² + 13.00² | = 21.64 mm |
Surface area
Surface area is calculated by multiplying the width and the height of a sensor.
LC1 sensor area
Width = 8.80 mm
Height = 6.60 mm
Surface area = 8.80 × 6.60 = 58.08 mm²
Height = 6.60 mm
Surface area = 8.80 × 6.60 = 58.08 mm²
GF3 sensor area
Width = 17.30 mm
Height = 13.00 mm
Surface area = 17.30 × 13.00 = 224.90 mm²
Height = 13.00 mm
Surface area = 17.30 × 13.00 = 224.90 mm²
Pixel pitch
Pixel pitch is the distance from the center of one pixel to the center of the
next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch = | sensor width in mm | × 1000 |
sensor resolution width in pixels |
LC1 pixel pitch
Sensor width = 8.80 mm
Sensor resolution width = 2552 pixels
Sensor resolution width = 2552 pixels
Pixel pitch = | 8.80 | × 1000 | = 3.45 µm |
2552 |
GF3 pixel pitch
Sensor width = 17.30 mm
Sensor resolution width = 4011 pixels
Sensor resolution width = 4011 pixels
Pixel pitch = | 17.30 | × 1000 | = 4.31 µm |
4011 |
Pixel area
The area of one pixel can be calculated by simply squaring the pixel pitch:
You could also divide sensor surface area with effective megapixels:
Pixel area = pixel pitch²
You could also divide sensor surface area with effective megapixels:
Pixel area = | sensor surface area in mm² |
effective megapixels |
LC1 pixel area
Pixel pitch = 3.45 µm
Pixel area = 3.45² = 11.9 µm²
Pixel area = 3.45² = 11.9 µm²
GF3 pixel area
Pixel pitch = 4.31 µm
Pixel area = 4.31² = 18.58 µm²
Pixel area = 4.31² = 18.58 µm²
Pixel density
Pixel density can be calculated with the following formula:
One could also use this formula:
Pixel density = ( | sensor resolution width in pixels | )² / 1000000 |
sensor width in cm |
One could also use this formula:
Pixel density = | effective megapixels × 1000000 | / 10000 |
sensor surface area in mm² |
LC1 pixel density
Sensor resolution width = 2552 pixels
Sensor width = 0.88 cm
Pixel density = (2552 / 0.88)² / 1000000 = 8.41 MP/cm²
Sensor width = 0.88 cm
Pixel density = (2552 / 0.88)² / 1000000 = 8.41 MP/cm²
GF3 pixel density
Sensor resolution width = 4011 pixels
Sensor width = 1.73 cm
Pixel density = (4011 / 1.73)² / 1000000 = 5.38 MP/cm²
Sensor width = 1.73 cm
Pixel density = (4011 / 1.73)² / 1000000 = 5.38 MP/cm²
Sensor resolution
Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher
than maximum (not interpolated) image resolution which is usually stated on camera specifications.
Sensor resolution is used in pixel pitch, pixel area, and pixel density formula.
For sake of simplicity, we're going to calculate it in 3 stages.
1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.
2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
3. To get sensor resolution we then multiply X with the corresponding ratio:
Resolution horizontal: X × r
Resolution vertical: X
1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.
2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000 → |
|
Resolution horizontal: X × r
Resolution vertical: X
LC1 sensor resolution
Sensor width = 8.80 mm
Sensor height = 6.60 mm
Effective megapixels = 4.90
Resolution horizontal: X × r = 1919 × 1.33 = 2552
Resolution vertical: X = 1919
Sensor resolution = 2552 x 1919
Sensor height = 6.60 mm
Effective megapixels = 4.90
r = 8.80/6.60 = 1.33 |
|
Resolution vertical: X = 1919
Sensor resolution = 2552 x 1919
GF3 sensor resolution
Sensor width = 17.30 mm
Sensor height = 13.00 mm
Effective megapixels = 12.10
Resolution horizontal: X × r = 3016 × 1.33 = 4011
Resolution vertical: X = 3016
Sensor resolution = 4011 x 3016
Sensor height = 13.00 mm
Effective megapixels = 12.10
r = 17.30/13.00 = 1.33 |
|
Resolution vertical: X = 3016
Sensor resolution = 4011 x 3016
Crop factor
Crop factor or focal length multiplier is calculated by dividing the diagonal
of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor = | 43.27 mm |
sensor diagonal in mm |
LC1 crop factor
Sensor diagonal in mm = 11.00 mm
Crop factor = | 43.27 | = 3.93 |
11.00 |
GF3 crop factor
Sensor diagonal in mm = 21.64 mm
Crop factor = | 43.27 | = 2 |
21.64 |
35 mm equivalent aperture
Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture
with crop factor (a.k.a. focal length multiplier).
LC1 equivalent aperture
Crop factor = 3.93
Aperture = f2.0 - f2.4
35-mm equivalent aperture = (f2.0 - f2.4) × 3.93 = f7.9 - f9.4
Aperture = f2.0 - f2.4
35-mm equivalent aperture = (f2.0 - f2.4) × 3.93 = f7.9 - f9.4
GF3 equivalent aperture
Aperture is a lens characteristic, so it's calculated only for
fixed lens cameras. If you want to know the equivalent aperture for
Panasonic GF3, take the aperture of the lens
you're using and multiply it with crop factor.
Crop factor for Panasonic GF3 is 2
Crop factor for Panasonic GF3 is 2
More comparisons of Panasonic LC1:
- Panasonic Lumix DMC-LC1 vs. Panasonic Lumix DMC-LX1
- Panasonic Lumix DMC-LC1 vs. Panasonic Lumix DMC-GH3
- Panasonic Lumix DMC-LC1 vs. Leica Digilux 1
- Panasonic Lumix DMC-LC1 vs. Olympus E-300 / EVOLT E-300
- Panasonic Lumix DMC-LC1 vs. Canon PowerShot G5
- Panasonic Lumix DMC-LC1 vs. Fujifilm X20
- Panasonic Lumix DMC-LC1 vs. Samsung NX100
- Panasonic Lumix DMC-LC1 vs. Sony Cyber-shot DSC-RX100 II
- Panasonic Lumix DMC-LC1 vs. Panasonic Lumix DMC-FZ50
- Panasonic Lumix DMC-LC1 vs. Fujifilm XF1
Enter your screen size (diagonal)
My screen size is
inches
Actual size is currently adjusted to screen.
If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.
If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.