AgfaPhoto Compact 100 vs. Canon PowerShot A1200

Comparison

change cameras »
Compact 100 image
vs
PowerShot A1200 image
AgfaPhoto Compact 100 Canon PowerShot A1200
check price » check price »
Megapixels
10.00
12.10
Max. image resolution
3648 x 2736
4000 x 3000

Sensor

Sensor type
CCD
CCD
Sensor size
1/2.5" (~ 5.75 x 4.32 mm)
1/2.3" (~ 6.16 x 4.62 mm)
Sensor resolution
3647 x 2742
4011 x 3016
Diagonal
7.19 mm
7.70 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1 : 1.15
(ratio)
AgfaPhoto Compact 100 Canon PowerShot A1200
Surface area:
24.84 mm² vs 28.46 mm²
Difference: 3.62 mm² (15%)
A1200 sensor is approx. 1.15x bigger than Compact 100 sensor.
Note: You are comparing cameras of different generations. There is a 2 year gap between AgfaPhoto Compact 100 (2009) and Canon A1200 (2011). All things being equal, newer sensor generations generally outperform the older.
Pixel pitch
1.58 µm
1.54 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 0.04 µm (3%)
Pixel pitch of Compact 100 is approx. 3% higher than pixel pitch of A1200.
Pixel area
2.5 µm²
2.37 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 0.13 µm² (5%)
A pixel on AgfaPhoto Compact 100 sensor is approx. 5% bigger than a pixel on Canon A1200.
Pixel density
40.23 MP/cm²
42.4 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 2.17 µm (5%)
Canon A1200 has approx. 5% higher pixel density than AgfaPhoto Compact 100.
To learn about the accuracy of these numbers, click here.



Specs

AgfaPhoto Compact 100
Canon A1200
Crop factor
6.02
5.62
Total megapixels
12.70
Effective megapixels
12.10
Optical zoom
Yes
4x
Digital zoom
Yes
Yes
ISO sensitivity
Auto, 50, 100, 200, 400, 800, 1600, 3200, 6400
Auto, 80, 100, 200, 400, 800, 1600
RAW
Manual focus
Normal focus range
80 cm
45 cm
Macro focus range
5 cm
3 cm
Focal length (35mm equiv.)
36 - 108 mm
28 - 112 mm
Aperture priority
No
No
Max. aperture
f3.0 - f5.6
f2.8 - f5.9
Max. aperture (35mm equiv.)
f18.1 - f33.7
f15.7 - f33.2
Metering
Centre weighted, Multi-segment, Spot
Centre weighted, Evaluative, Spot
Exposure compensation
±2 EV (in 1/3 EV steps)
±2 EV (in 1/3 EV steps)
Shutter priority
No
No
Min. shutter speed
1 sec
15 sec
Max. shutter speed
1/2000 sec
1/1600 sec
Built-in flash
External flash
Viewfinder
None
Optical (tunnel)
White balance presets
6
6
Screen size
2.7"
2.7"
Screen resolution
230,400 dots
230,000 dots
Video capture
Max. video resolution
Storage types
SDHC, Secure Digital
SDHC, SDXC, Secure Digital
USB
USB 2.0 (480 Mbit/sec)
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
2x AA
2 x AA batteries
Weight
125 g
185 g
Dimensions
91 x 60.5 x 23.5 mm
97.5 x 62.5 x 30.7 mm
Year
2009
2011




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

AgfaPhoto Compact 100 diagonal

The diagonal of Compact 100 sensor is not 1/2.5 or 0.4" (10.2 mm) as you might expect, but approximately two thirds of that value - 7.19 mm. If you want to know why, see sensor sizes.

w = 5.75 mm
h = 4.32 mm
Diagonal =  5.75² + 4.32²   = 7.19 mm

Canon A1200 diagonal

The diagonal of A1200 sensor is not 1/2.3 or 0.43" (11 mm) as you might expect, but approximately two thirds of that value - 7.7 mm. If you want to know why, see sensor sizes.

w = 6.16 mm
h = 4.62 mm
Diagonal =  6.16² + 4.62²   = 7.70 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

Compact 100 sensor area

Width = 5.75 mm
Height = 4.32 mm

Surface area = 5.75 × 4.32 = 24.84 mm²

A1200 sensor area

Width = 6.16 mm
Height = 4.62 mm

Surface area = 6.16 × 4.62 = 28.46 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

Compact 100 pixel pitch

Sensor width = 5.75 mm
Sensor resolution width = 3647 pixels
Pixel pitch =   5.75  × 1000  = 1.58 µm
3647

A1200 pixel pitch

Sensor width = 6.16 mm
Sensor resolution width = 4011 pixels
Pixel pitch =   6.16  × 1000  = 1.54 µm
4011


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

Compact 100 pixel area

Pixel pitch = 1.58 µm

Pixel area = 1.58² = 2.5 µm²

A1200 pixel area

Pixel pitch = 1.54 µm

Pixel area = 1.54² = 2.37 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

Compact 100 pixel density

Sensor resolution width = 3647 pixels
Sensor width = 0.575 cm

Pixel density = (3647 / 0.575)² / 1000000 = 40.23 MP/cm²

A1200 pixel density

Sensor resolution width = 4011 pixels
Sensor width = 0.616 cm

Pixel density = (4011 / 0.616)² / 1000000 = 42.4 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

Compact 100 sensor resolution

Sensor width = 5.75 mm
Sensor height = 4.32 mm
Effective megapixels = 10.00
r = 5.75/4.32 = 1.33
X =  10.00 × 1000000  = 2742
1.33
Resolution horizontal: X × r = 2742 × 1.33 = 3647
Resolution vertical: X = 2742

Sensor resolution = 3647 x 2742

A1200 sensor resolution

Sensor width = 6.16 mm
Sensor height = 4.62 mm
Effective megapixels = 12.10
r = 6.16/4.62 = 1.33
X =  12.10 × 1000000  = 3016
1.33
Resolution horizontal: X × r = 3016 × 1.33 = 4011
Resolution vertical: X = 3016

Sensor resolution = 4011 x 3016


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


Compact 100 crop factor

Sensor diagonal in mm = 7.19 mm
Crop factor =   43.27  = 6.02
7.19

A1200 crop factor

Sensor diagonal in mm = 7.70 mm
Crop factor =   43.27  = 5.62
7.70

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

Compact 100 equivalent aperture

Crop factor = 6.02
Aperture = f3.0 - f5.6

35-mm equivalent aperture = (f3.0 - f5.6) × 6.02 = f18.1 - f33.7

A1200 equivalent aperture

Crop factor = 5.62
Aperture = f2.8 - f5.9

35-mm equivalent aperture = (f2.8 - f5.9) × 5.62 = f15.7 - f33.2

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.