Canon EOS M50 II vs. Canon EOS 7D Mark II

Comparison

change cameras »
EOS M50 II image
vs
EOS 7D Mark II image
Canon EOS M50 II Canon EOS 7D Mark II
check price » check price »
Megapixels
24.10
20.20
Max. image resolution
6000 x 4000
5472 x 3648

Sensor

Sensor type
CMOS
CMOS
Sensor size
22.3 x 14.9 mm
22.4 x 15 mm
Sensor resolution
6012 x 4008
5486 x 3682
Diagonal
26.82 mm
26.96 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1 : 1.01
(ratio)
Canon EOS M50 II Canon EOS 7D Mark II
Surface area:
332.27 mm² vs 336.00 mm²
Difference: 3.73 mm² (1%)
7D Mark II sensor is slightly bigger than M50 II sensor (only 1% difference).
Note: You are comparing sensors of very different generations. There is a gap of 6 years between Canon M50 II ( 2020) and Canon 7D Mark II (2014). Six years is a lot of time in terms of technology, meaning newer sensors are overall much more efficient than the older ones.
Pixel pitch
3.71 µm
4.08 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 0.37 µm (10%)
Pixel pitch of 7D Mark II is approx. 10% higher than pixel pitch of M50 II.
Pixel area
13.76 µm²
16.65 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 2.89 µm² (21%)
A pixel on Canon 7D Mark II sensor is approx. 21% bigger than a pixel on Canon M50 II.
Pixel density
7.27 MP/cm²
6 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 1.27 µm (21%)
Canon M50 II has approx. 21% higher pixel density than Canon 7D Mark II.
To learn about the accuracy of these numbers, click here.



Specs

Canon M50 II
Canon 7D Mark II
Crop factor
1.61
1.6
Total megapixels
25.80
20.90
Effective megapixels
24.10
20.20
Optical zoom
Digital zoom
ISO sensitivity
Auto, 100-25600 (extends to 51200)
Auto, 100-16000 (expandable to 51200)
RAW
Manual focus
Normal focus range
Macro focus range
Focal length (35mm equiv.)
Aperture priority
Yes
Yes
Max. aperture
Max. aperture (35mm equiv.)
n/a
n/a
Metering
Multi, Center-weighted, Spot
Evaluative, Partial, Center-weighted, Spot
Exposure compensation
±3 EV (in 1/3 EV steps)
±5 EV (in 1/3 EV, 1/2 EV steps)
Shutter priority
Yes
Yes
Min. shutter speed
30 sec
30 sec
Max. shutter speed
1/4000 sec
1/8000 sec
Built-in flash
External flash
Viewfinder
Electronic
Optical (pentaprism)
White balance presets
7
8
Screen size
3"
3"
Screen resolution
1,040,000 dots
1,040,000 dots
Video capture
Max. video resolution
3840x2160 (24p/​25p)
1920x1080 (60p/50p/30p/25p/24p)
Storage types
SD/SDHC/SDXC
SD/SDHC/SDXC/Type I CompactFlash
USB
USB 2.0 (480 Mbit/sec)
USB 3.0 (5 GBit/sec)
HDMI
Wireless
GPS
Battery
LP-E12 lithium-ion battery
Battery Pack LP-E6N (or LP-E6)
Weight
387 g
910 g
Dimensions
116.3 x 88.1 x 58.7 mm
148.6 x 112.4 x 78.2 mm
Year
2020
2014




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Canon M50 II diagonal

w = 22.30 mm
h = 14.90 mm
Diagonal =  22.30² + 14.90²   = 26.82 mm

Canon 7D Mark II diagonal

w = 22.40 mm
h = 15.00 mm
Diagonal =  22.40² + 15.00²   = 26.96 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

M50 II sensor area

Width = 22.30 mm
Height = 14.90 mm

Surface area = 22.30 × 14.90 = 332.27 mm²

7D Mark II sensor area

Width = 22.40 mm
Height = 15.00 mm

Surface area = 22.40 × 15.00 = 336.00 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

M50 II pixel pitch

Sensor width = 22.30 mm
Sensor resolution width = 6012 pixels
Pixel pitch =   22.30  × 1000  = 3.71 µm
6012

7D Mark II pixel pitch

Sensor width = 22.40 mm
Sensor resolution width = 5486 pixels
Pixel pitch =   22.40  × 1000  = 4.08 µm
5486


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

M50 II pixel area

Pixel pitch = 3.71 µm

Pixel area = 3.71² = 13.76 µm²

7D Mark II pixel area

Pixel pitch = 4.08 µm

Pixel area = 4.08² = 16.65 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

M50 II pixel density

Sensor resolution width = 6012 pixels
Sensor width = 2.23 cm

Pixel density = (6012 / 2.23)² / 1000000 = 7.27 MP/cm²

7D Mark II pixel density

Sensor resolution width = 5486 pixels
Sensor width = 2.24 cm

Pixel density = (5486 / 2.24)² / 1000000 = 6 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

M50 II sensor resolution

Sensor width = 22.30 mm
Sensor height = 14.90 mm
Effective megapixels = 24.10
r = 22.30/14.90 = 1.5
X =  24.10 × 1000000  = 4008
1.5
Resolution horizontal: X × r = 4008 × 1.5 = 6012
Resolution vertical: X = 4008

Sensor resolution = 6012 x 4008

7D Mark II sensor resolution

Sensor width = 22.40 mm
Sensor height = 15.00 mm
Effective megapixels = 20.20
r = 22.40/15.00 = 1.49
X =  20.20 × 1000000  = 3682
1.49
Resolution horizontal: X × r = 3682 × 1.49 = 5486
Resolution vertical: X = 3682

Sensor resolution = 5486 x 3682


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


M50 II crop factor

Sensor diagonal in mm = 26.82 mm
Crop factor =   43.27  = 1.61
26.82

7D Mark II crop factor

Sensor diagonal in mm = 26.96 mm
Crop factor =   43.27  = 1.6
26.96

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

M50 II equivalent aperture

Aperture is a lens characteristic, so it's calculated only for fixed lens cameras. If you want to know the equivalent aperture for Canon M50 II, take the aperture of the lens you're using and multiply it with crop factor.

Crop factor for Canon M50 II is 1.61

7D Mark II equivalent aperture

Aperture is a lens characteristic, so it's calculated only for fixed lens cameras. If you want to know the equivalent aperture for Canon 7D Mark II, take the aperture of the lens you're using and multiply it with crop factor.

Crop factor for Canon 7D Mark II is 1.6

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.