Canon EOS R5 vs. Olympus OM-D E-M1 Mark III

Comparison

change cameras »
EOS R5 image
vs
OM-D E-M1 Mark III image
Canon EOS R5 Olympus OM-D E-M1 Mark III
check price » check price »
Megapixels
45.00
20.40
Max. image resolution
8192 x 5464
5184 x 3888

Sensor

Sensor type
CMOS
CMOS
Sensor size
36 x 24 mm
Four Thirds (17.3 x 13 mm)
Sensor resolution
8216 x 5477
5208 x 3916
Diagonal
43.27 mm
21.64 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
3.84 : 1
(ratio)
Canon EOS R5 Olympus OM-D E-M1 Mark III
Surface area:
864.00 mm² vs 224.90 mm²
Difference: 639.1 mm² (284%)
R5 sensor is approx. 3.84x bigger than OM-D E-M1 Mark III sensor.
Pixel pitch
4.38 µm
3.32 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 1.06 µm (32%)
Pixel pitch of R5 is approx. 32% higher than pixel pitch of OM-D E-M1 Mark III.
Pixel area
19.18 µm²
11.02 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 8.16 µm² (74%)
A pixel on Canon R5 sensor is approx. 74% bigger than a pixel on Olympus OM-D E-M1 Mark III.
Pixel density
5.21 MP/cm²
9.06 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 3.85 µm (74%)
Olympus OM-D E-M1 Mark III has approx. 74% higher pixel density than Canon R5.
To learn about the accuracy of these numbers, click here.



Specs

Canon R5
Olympus OM-D E-M1 Mark III
Crop factor
1
2
Total megapixels
47.10
21.80
Effective megapixels
45.00
20.40
Optical zoom
 
Digital zoom
Yes
ISO sensitivity
Yes, 100-51200 (extends to 50-102400)
Auto, 200-25600 (extendable to 64)
RAW
Manual focus
Normal focus range
Macro focus range
Focal length (35mm equiv.)
Aperture priority
Yes
Yes
Max. aperture
Max. aperture (35mm equiv.)
n/a
n/a
Metering
Multi, Center-weighted, Spot, Partial
Multi, Center-weighted, Highlight-weighted, Spot
Exposure compensation
±3 EV (in 1/3 EV, 1/2 EV steps)
±5 EV (in 1/3 EV, 1/2 EV, 1 EV steps)
Shutter priority
Yes
Yes
Min. shutter speed
30 sec
60 sec
Max. shutter speed
1/8000 sec
1/32000 sec
Built-in flash
External flash
Viewfinder
Electronic
Electronic
White balance presets
8
7
Screen size
3.2"
3"
Screen resolution
2,100,000 dots
1,037,000 dots
Video capture
Max. video resolution
8192x4320 (30p/​24/​23.98p)
4096x2160 (24p)
Storage types
SD/SDHC/SDXC/CFexpress
SD/SDHC/SDXC
USB
USB 3.0 (5 GBit/sec)
USB 3.0 (5 GBit/sec)
HDMI
Wireless
GPS
Battery
LP-E6NH lithium-ion battery
BLH-1 lithium-ion battery
Weight
738 g
580 g
Dimensions
138.5 x 97.5 x 88 mm
134.1 x 90.9 x 68.9 mm
Year
2020
2020




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Canon R5 diagonal

w = 36.00 mm
h = 24.00 mm
Diagonal =  36.00² + 24.00²   = 43.27 mm

Olympus OM-D E-M1 Mark III diagonal

w = 17.30 mm
h = 13.00 mm
Diagonal =  17.30² + 13.00²   = 21.64 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

R5 sensor area

Width = 36.00 mm
Height = 24.00 mm

Surface area = 36.00 × 24.00 = 864.00 mm²

OM-D E-M1 Mark III sensor area

Width = 17.30 mm
Height = 13.00 mm

Surface area = 17.30 × 13.00 = 224.90 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

R5 pixel pitch

Sensor width = 36.00 mm
Sensor resolution width = 8216 pixels
Pixel pitch =   36.00  × 1000  = 4.38 µm
8216

OM-D E-M1 Mark III pixel pitch

Sensor width = 17.30 mm
Sensor resolution width = 5208 pixels
Pixel pitch =   17.30  × 1000  = 3.32 µm
5208


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

R5 pixel area

Pixel pitch = 4.38 µm

Pixel area = 4.38² = 19.18 µm²

OM-D E-M1 Mark III pixel area

Pixel pitch = 3.32 µm

Pixel area = 3.32² = 11.02 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

R5 pixel density

Sensor resolution width = 8216 pixels
Sensor width = 3.6 cm

Pixel density = (8216 / 3.6)² / 1000000 = 5.21 MP/cm²

OM-D E-M1 Mark III pixel density

Sensor resolution width = 5208 pixels
Sensor width = 1.73 cm

Pixel density = (5208 / 1.73)² / 1000000 = 9.06 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

R5 sensor resolution

Sensor width = 36.00 mm
Sensor height = 24.00 mm
Effective megapixels = 45.00
r = 36.00/24.00 = 1.5
X =  45.00 × 1000000  = 5477
1.5
Resolution horizontal: X × r = 5477 × 1.5 = 8216
Resolution vertical: X = 5477

Sensor resolution = 8216 x 5477

OM-D E-M1 Mark III sensor resolution

Sensor width = 17.30 mm
Sensor height = 13.00 mm
Effective megapixels = 20.40
r = 17.30/13.00 = 1.33
X =  20.40 × 1000000  = 3916
1.33
Resolution horizontal: X × r = 3916 × 1.33 = 5208
Resolution vertical: X = 3916

Sensor resolution = 5208 x 3916


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


R5 crop factor

Sensor diagonal in mm = 43.27 mm
Crop factor =   43.27  = 1
43.27

OM-D E-M1 Mark III crop factor

Sensor diagonal in mm = 21.64 mm
Crop factor =   43.27  = 2
21.64

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

R5 equivalent aperture

Aperture is a lens characteristic, so it's calculated only for fixed lens cameras. If you want to know the equivalent aperture for Canon R5, take the aperture of the lens you're using and multiply it with crop factor.

Since crop factor for Canon R5 is 1, the equivalent aperture is aperture.

OM-D E-M1 Mark III equivalent aperture

Aperture is a lens characteristic, so it's calculated only for fixed lens cameras. If you want to know the equivalent aperture for Olympus OM-D E-M1 Mark III, take the aperture of the lens you're using and multiply it with crop factor.

Crop factor for Olympus OM-D E-M1 Mark III is 2

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.