Canon PowerShot SD200 vs. Fujifilm FinePix HS35 EXR

Comparison

change cameras »
PowerShot SD200 image
vs
FinePix HS35 EXR image
Canon PowerShot SD200 Fujifilm FinePix HS35 EXR
check price » check price »
Megapixels
3.20
16.00
Max. image resolution
2048 x 1536
4608 x 3456

Sensor

Sensor type
CCD
CMOS
Sensor size
1/2.5" (~ 5.75 x 4.32 mm)
1/2" (~ 6.4 x 4.8 mm)
Sensor resolution
2063 x 1551
4612 x 3468
Diagonal
7.19 mm
8.00 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1 : 1.24
(ratio)
Canon PowerShot SD200 Fujifilm FinePix HS35 EXR
Surface area:
24.84 mm² vs 30.72 mm²
Difference: 5.88 mm² (24%)
HS35 EXR sensor is approx. 1.24x bigger than SD200 sensor.
Note: You are comparing sensors of very different generations. There is a gap of 9 years between Canon SD200 (2004) and Fujifilm HS35 EXR (2013). Nine years is a lot of time in terms of technology, meaning newer sensors are overall much more efficient than the older ones.
Pixel pitch
2.79 µm
1.39 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 1.4 µm (101%)
Pixel pitch of SD200 is approx. 101% higher than pixel pitch of HS35 EXR.
Pixel area
7.78 µm²
1.93 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 5.85 µm² (303%)
A pixel on Canon SD200 sensor is approx. 303% bigger than a pixel on Fujifilm HS35 EXR.
Pixel density
12.87 MP/cm²
51.93 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 39.06 µm (303%)
Fujifilm HS35 EXR has approx. 303% higher pixel density than Canon SD200.
To learn about the accuracy of these numbers, click here.



Specs

Canon SD200
Fujifilm HS35 EXR
Crop factor
6.02
5.41
Total megapixels
3.30
Effective megapixels
3.20
16.00
Optical zoom
3x
30x
Digital zoom
Yes
Yes
ISO sensitivity
Auto, 50, 100, 200, 400
Auto, 100, 200, 400, 800, 1600, 3200, 6400, 12800
RAW
Manual focus
Normal focus range
50 cm
45 cm
Macro focus range
3 cm
1 cm
Focal length (35mm equiv.)
35 - 105 mm
24 - 720 mm
Aperture priority
No
Yes
Max. aperture
f2.8 - f4.9
f2.8 - f5.6
Max. aperture (35mm equiv.)
f16.9 - f29.5
f15.1 - f30.3
Metering
Multi, Center-weighted, Spot
Multi, Average, Spot
Exposure compensation
±2 EV (in 1/3 EV steps)
±2 EV (in 1/3 EV steps)
Shutter priority
No
Yes
Min. shutter speed
15 sec
30 sec
Max. shutter speed
1/1500 sec
1/4000 sec
Built-in flash
External flash
Viewfinder
Optical (tunnel)
Electronic
White balance presets
5
6
Screen size
2"
3"
Screen resolution
118,000 dots
460,000 dots
Video capture
Max. video resolution
1920x1080 (30p)
Storage types
SD card
SD/SDHC/SDXC
USB
USB 1.0
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
Lithium-Ion NB-4L battery
Li-ion battery NP-W126
Weight
135 g
687 g
Dimensions
86 x 54 x 21 mm
130.6 x 96.6 x 126 mm
Year
2004
2013




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Canon SD200 diagonal

The diagonal of SD200 sensor is not 1/2.5 or 0.4" (10.2 mm) as you might expect, but approximately two thirds of that value - 7.19 mm. If you want to know why, see sensor sizes.

w = 5.75 mm
h = 4.32 mm
Diagonal =  5.75² + 4.32²   = 7.19 mm

Fujifilm HS35 EXR diagonal

The diagonal of HS35 EXR sensor is not 1/2 or 0.5" (12.7 mm) as you might expect, but approximately two thirds of that value - 8 mm. If you want to know why, see sensor sizes.

w = 6.40 mm
h = 4.80 mm
Diagonal =  6.40² + 4.80²   = 8.00 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

SD200 sensor area

Width = 5.75 mm
Height = 4.32 mm

Surface area = 5.75 × 4.32 = 24.84 mm²

HS35 EXR sensor area

Width = 6.40 mm
Height = 4.80 mm

Surface area = 6.40 × 4.80 = 30.72 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

SD200 pixel pitch

Sensor width = 5.75 mm
Sensor resolution width = 2063 pixels
Pixel pitch =   5.75  × 1000  = 2.79 µm
2063

HS35 EXR pixel pitch

Sensor width = 6.40 mm
Sensor resolution width = 4612 pixels
Pixel pitch =   6.40  × 1000  = 1.39 µm
4612


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

SD200 pixel area

Pixel pitch = 2.79 µm

Pixel area = 2.79² = 7.78 µm²

HS35 EXR pixel area

Pixel pitch = 1.39 µm

Pixel area = 1.39² = 1.93 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

SD200 pixel density

Sensor resolution width = 2063 pixels
Sensor width = 0.575 cm

Pixel density = (2063 / 0.575)² / 1000000 = 12.87 MP/cm²

HS35 EXR pixel density

Sensor resolution width = 4612 pixels
Sensor width = 0.64 cm

Pixel density = (4612 / 0.64)² / 1000000 = 51.93 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

SD200 sensor resolution

Sensor width = 5.75 mm
Sensor height = 4.32 mm
Effective megapixels = 3.20
r = 5.75/4.32 = 1.33
X =  3.20 × 1000000  = 1551
1.33
Resolution horizontal: X × r = 1551 × 1.33 = 2063
Resolution vertical: X = 1551

Sensor resolution = 2063 x 1551

HS35 EXR sensor resolution

Sensor width = 6.40 mm
Sensor height = 4.80 mm
Effective megapixels = 16.00
r = 6.40/4.80 = 1.33
X =  16.00 × 1000000  = 3468
1.33
Resolution horizontal: X × r = 3468 × 1.33 = 4612
Resolution vertical: X = 3468

Sensor resolution = 4612 x 3468


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


SD200 crop factor

Sensor diagonal in mm = 7.19 mm
Crop factor =   43.27  = 6.02
7.19

HS35 EXR crop factor

Sensor diagonal in mm = 8.00 mm
Crop factor =   43.27  = 5.41
8.00

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

SD200 equivalent aperture

Crop factor = 6.02
Aperture = f2.8 - f4.9

35-mm equivalent aperture = (f2.8 - f4.9) × 6.02 = f16.9 - f29.5

HS35 EXR equivalent aperture

Crop factor = 5.41
Aperture = f2.8 - f5.6

35-mm equivalent aperture = (f2.8 - f5.6) × 5.41 = f15.1 - f30.3

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.