Fujifilm FinePix HS20 EXR vs. Fujifilm FinePix HS22 EXR

Comparison

change cameras »

Fujifilm FinePix HS20 EXR

Fujifilm FinePix HS22 EXR

check price »

Megapixels

16.00

Max. image resolution

4608 x 3456

Sensor

Sensor type

CMOS

Sensor size

1/2" (~ 6.4 x 4.8 mm)

Sensor resolution

4612 x 3468

Diagonal

8.00 mm

Sensor size comparison

Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »

	vs
1	:	1
(ratio)

Fujifilm FinePix HS20 EXR		Fujifilm FinePix HS22 EXR

Surface area:

30.72 mm²

Difference: 0 mm² (0%)

HS20 EXR and HS22 EXR sensors are the same size.

Pixel pitch

1.39 µm

Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.

Difference: 0 µm (0%)

HS20 EXR and HS22 EXR have the same pixel pitch.

Pixel area

1.93 µm²

Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.

Relative pixel sizes:

Pixel area difference: 0 µm² (0%)

Fujifilm HS20 EXR and Fujifilm HS22 EXR have the same pixel area.

Pixel density

51.93 MP/cm²

Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.

Difference: 0 µm (0%)

Fujifilm HS20 EXR and Fujifilm HS22 EXR have the same pixel density.

To learn about the accuracy of these numbers, click here.

Specs

Fujifilm HS20 EXR

Fujifilm HS22 EXR

Crop factor

5.41

Total megapixels

Effective megapixels

16.00

Optical zoom

30x

Digital zoom

ISO sensitivity

Auto, 100, 200, 400, 800, 1600, 3200 (6400 and 12800 with boost)

RAW

Manual focus

Normal focus range

50 cm

Macro focus range

1 cm

Focal length (35mm equiv.)

24 - 720 mm

Aperture priority

Yes

Max. aperture

f2.8 - f5.6

Max. aperture (35mm equiv.)

f15.1 - f30.3

Metering

Multi, Average, Spot

Multi-segment, Spot, TTL 256-zones metering

Exposure compensation

±2 EV (in 1/3 EV steps)

Shutter priority

Yes

Min. shutter speed

30 sec

Max. shutter speed

1/4000 sec

Built-in flash

External flash

Viewfinder

Electronic

White balance presets

Screen size

Screen resolution

460,000 dots

Video capture

Max. video resolution

Storage types

SD/SDHC/SDXC

SDHC, SDXC, Secure Digital

USB

USB 2.0 (480 Mbit/sec)

HDMI

Wireless

GPS

Battery

4 x AA batteries (Alkaline, NiMH or Lithium)

Weight

730 g

Dimensions

131 x 91 x 126 mm

Year

2011

Choose cameras to compare

Popular comparisons:

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:

Diagonal = √

w² + h²

where w = sensor width and h = sensor height

Fujifilm HS20 EXR diagonal

The diagonal of HS20 EXR sensor is not 1/2 or 0.5" (12.7 mm) as you might expect, but approximately two thirds of that value - 8 mm. If you want to know why, see sensor sizes.

w = 6.40 mm
h = 4.80 mm

Diagonal = √

6.40² + 4.80²

= 8.00 mm

Fujifilm HS22 EXR diagonal

The diagonal of HS22 EXR sensor is not 1/2 or 0.5" (12.7 mm) as you might expect, but approximately two thirds of that value - 8 mm. If you want to know why, see sensor sizes.

w = 6.40 mm
h = 4.80 mm

Diagonal = √

6.40² + 4.80²

= 8.00 mm

Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

HS20 EXR sensor area

Width = 6.40 mm
Height = 4.80 mm

Surface area = 6.40 × 4.80 = 30.72 mm²

HS22 EXR sensor area

Width = 6.40 mm
Height = 4.80 mm

Surface area = 6.40 × 4.80 = 30.72 mm²

Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:

Pixel pitch =	sensor width in mm	× 1000
	sensor resolution width in pixels

HS20 EXR pixel pitch

Sensor width = 6.40 mm
Sensor resolution width = 4612 pixels

Pixel pitch =	6.40	× 1000	= 1.39 µm
	4612

HS22 EXR pixel pitch

Sensor width = 6.40 mm
Sensor resolution width = 4612 pixels

Pixel pitch =	6.40	× 1000	= 1.39 µm
	4612

Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:

Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:

Pixel area =	sensor surface area in mm²
	effective megapixels

HS20 EXR pixel area

Pixel pitch = 1.39 µm

Pixel area = 1.39² = 1.93 µm²

HS22 EXR pixel area

Pixel pitch = 1.39 µm

Pixel area = 1.39² = 1.93 µm²

Pixel density

Pixel density can be calculated with the following formula:

Pixel density = (	sensor resolution width in pixels	)² / 1000000
	sensor width in cm

One could also use this formula:

Pixel density =	effective megapixels × 1000000	/ 10000
	sensor surface area in mm²

HS20 EXR pixel density

Sensor resolution width = 4612 pixels
Sensor width = 0.64 cm

Pixel density = (4612 / 0.64)² / 1000000 = 51.93 MP/cm²

HS22 EXR pixel density

Sensor resolution width = 4612 pixels
Sensor width = 0.64 cm

Pixel density = (4612 / 0.64)² / 1000000 = 51.93 MP/cm²

Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:

(X × r) × X = effective megapixels × 1000000 →

X = √	effective megapixels × 1000000
	r

3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

HS20 EXR sensor resolution

Sensor width = 6.40 mm
Sensor height = 4.80 mm
Effective megapixels = 16.00

r = 6.40/4.80 = 1.33

X = √	16.00 × 1000000	= 3468
	1.33

Resolution horizontal: X × r = 3468 × 1.33 = 4612
Resolution vertical: X = 3468

Sensor resolution = 4612 x 3468

HS22 EXR sensor resolution

Sensor width = 6.40 mm
Sensor height = 4.80 mm
Effective megapixels = 16.00

r = 6.40/4.80 = 1.33

X = √	16.00 × 1000000	= 3468
	1.33

Resolution horizontal: X × r = 3468 × 1.33 = 4612
Resolution vertical: X = 3468

Sensor resolution = 4612 x 3468

Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.

Crop factor =	43.27 mm
	sensor diagonal in mm

HS20 EXR crop factor

Sensor diagonal in mm = 8.00 mm

Crop factor =	43.27	= 5.41
	8.00

HS22 EXR crop factor

Sensor diagonal in mm = 8.00 mm

Crop factor =	43.27	= 5.41
	8.00

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

HS20 EXR equivalent aperture

Crop factor = 5.41
Aperture = f2.8 - f5.6

35-mm equivalent aperture = (f2.8 - f5.6) × 5.41 = f15.1 - f30.3

HS22 EXR equivalent aperture

Crop factor = 5.41
Aperture = f2.8 - f5.6

35-mm equivalent aperture = (f2.8 - f5.6) × 5.41 = f15.1 - f30.3

More comparisons of Fujifilm HS20 EXR:

Enter your screen size (diagonal)

My screen size is inches

Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.