Fujifilm X-T30 vs. Panasonic Lumix DC-S1

Comparison

change cameras »
X-T30 image
vs
Lumix DC-S1 image
Fujifilm X-T30 Panasonic Lumix DC-S1
check price » check price »
Megapixels
26.10
24.20
Max. image resolution
6240 x 4160
6000 x 4000

Sensor

Sensor type
CMOS
CMOS
Sensor size
23.5 x 15.6 mm
35.6 x 23.8 mm
Sensor resolution
6277 x 4157
6026 x 4017
Diagonal
28.21 mm
42.82 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1 : 2.31
(ratio)
Fujifilm X-T30 Panasonic Lumix DC-S1
Surface area:
366.60 mm² vs 847.28 mm²
Difference: 480.68 mm² (131%)
Lumix DC-S1 sensor is approx. 2.31x bigger than X-T30 sensor.
Pixel pitch
3.74 µm
5.91 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 2.17 µm (58%)
Pixel pitch of Lumix DC-S1 is approx. 58% higher than pixel pitch of X-T30.
Pixel area
13.99 µm²
34.93 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 20.94 µm² (150%)
A pixel on Panasonic Lumix DC-S1 sensor is approx. 150% bigger than a pixel on Fujifilm X-T30.
Pixel density
7.13 MP/cm²
2.87 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 4.26 µm (148%)
Fujifilm X-T30 has approx. 148% higher pixel density than Panasonic Lumix DC-S1.
To learn about the accuracy of these numbers, click here.



Specs

Fujifilm X-T30
Panasonic Lumix DC-S1
Crop factor
1.53
1.01
Total megapixels
25.28
Effective megapixels
26.10
24.20
Optical zoom
Digital zoom
Yes
ISO sensitivity
Auto, 160-12800 (extends to 80-51200)
Auto, 100-51200 (extends to 50-204800)
RAW
Manual focus
Normal focus range
Macro focus range
Focal length (35mm equiv.)
Aperture priority
Yes
Yes
Max. aperture
Max. aperture (35mm equiv.)
n/a
n/a
Metering
Multi, Center-weighted, Average, Spot
Multi, Center-weighted, Highlight-weighted, Spot
Exposure compensation
±5 EV (in 1/3 EV steps)
±5 EV (in 1/3 EV steps)
Shutter priority
Yes
Yes
Min. shutter speed
30 sec
60 sec
Max. shutter speed
1/4000 sec
1/8000 sec
Built-in flash
External flash
Viewfinder
Electronic
Electronic
White balance presets
7
8
Screen size
3"
3.2"
Screen resolution
1,040,000 dots
2,100,000 dots
Video capture
Max. video resolution
4096x2160 (30p/25p/24p)
3840x2160 (60p/30p/24p)
Storage types
SD/SDHC/SDXC
SD/SDHC/SDXC/XQD
USB
USB 3.0 (5 GBit/sec)
USB 3.0 (5 GBit/sec)
HDMI
Wireless
GPS
Battery
NP-W126S Li-ion battery
Li-ion Battery Pack
Weight
383 g
1021 g
Dimensions
118.4 x 82.8 x 46.8 mm
148.9 x 110 x 96.7 mm
Year
2019
2019




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Fujifilm X-T30 diagonal

w = 23.50 mm
h = 15.60 mm
Diagonal =  23.50² + 15.60²   = 28.21 mm

Panasonic Lumix DC-S1 diagonal

w = 35.60 mm
h = 23.80 mm
Diagonal =  35.60² + 23.80²   = 42.82 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

X-T30 sensor area

Width = 23.50 mm
Height = 15.60 mm

Surface area = 23.50 × 15.60 = 366.60 mm²

Lumix DC-S1 sensor area

Width = 35.60 mm
Height = 23.80 mm

Surface area = 35.60 × 23.80 = 847.28 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

X-T30 pixel pitch

Sensor width = 23.50 mm
Sensor resolution width = 6277 pixels
Pixel pitch =   23.50  × 1000  = 3.74 µm
6277

Lumix DC-S1 pixel pitch

Sensor width = 35.60 mm
Sensor resolution width = 6026 pixels
Pixel pitch =   35.60  × 1000  = 5.91 µm
6026


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

X-T30 pixel area

Pixel pitch = 3.74 µm

Pixel area = 3.74² = 13.99 µm²

Lumix DC-S1 pixel area

Pixel pitch = 5.91 µm

Pixel area = 5.91² = 34.93 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

X-T30 pixel density

Sensor resolution width = 6277 pixels
Sensor width = 2.35 cm

Pixel density = (6277 / 2.35)² / 1000000 = 7.13 MP/cm²

Lumix DC-S1 pixel density

Sensor resolution width = 6026 pixels
Sensor width = 3.56 cm

Pixel density = (6026 / 3.56)² / 1000000 = 2.87 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

X-T30 sensor resolution

Sensor width = 23.50 mm
Sensor height = 15.60 mm
Effective megapixels = 26.10
r = 23.50/15.60 = 1.51
X =  26.10 × 1000000  = 4157
1.51
Resolution horizontal: X × r = 4157 × 1.51 = 6277
Resolution vertical: X = 4157

Sensor resolution = 6277 x 4157

Lumix DC-S1 sensor resolution

Sensor width = 35.60 mm
Sensor height = 23.80 mm
Effective megapixels = 24.20
r = 35.60/23.80 = 1.5
X =  24.20 × 1000000  = 4017
1.5
Resolution horizontal: X × r = 4017 × 1.5 = 6026
Resolution vertical: X = 4017

Sensor resolution = 6026 x 4017


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


X-T30 crop factor

Sensor diagonal in mm = 28.21 mm
Crop factor =   43.27  = 1.53
28.21

Lumix DC-S1 crop factor

Sensor diagonal in mm = 42.82 mm
Crop factor =   43.27  = 1.01
42.82

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

X-T30 equivalent aperture

Aperture is a lens characteristic, so it's calculated only for fixed lens cameras. If you want to know the equivalent aperture for Fujifilm X-T30, take the aperture of the lens you're using and multiply it with crop factor.

Crop factor for Fujifilm X-T30 is 1.53

Lumix DC-S1 equivalent aperture

Aperture is a lens characteristic, so it's calculated only for fixed lens cameras. If you want to know the equivalent aperture for Panasonic Lumix DC-S1, take the aperture of the lens you're using and multiply it with crop factor.

Crop factor for Panasonic Lumix DC-S1 is 1.01

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.