Konica-Minolta DiMAGE A2 vs. Canon EOS 5D Mark III

Comparison

change cameras »
DiMAGE A2 image
vs
EOS 5D Mark III image
Konica-Minolta DiMAGE A2 Canon EOS 5D Mark III
check price » check price »
Megapixels
8.00
22.30
Max. image resolution
3264 x 2448
5760 x 3840

Sensor

Sensor type
CCD
CMOS
Sensor size
2/3" (~ 8.8 x 6.6 mm)
36 x 24 mm
Sensor resolution
3262 x 2453
5784 x 3856
Diagonal
11.00 mm
43.27 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1 : 14.88
(ratio)
Konica-Minolta DiMAGE A2 Canon EOS 5D Mark III
Surface area:
58.08 mm² vs 864.00 mm²
Difference: 805.92 mm² (1388%)
5D Mark III sensor is approx. 14.88x bigger than DiMAGE A2 sensor.
Note: You are comparing sensors of very different generations. There is a gap of 8 years between Konica-Minolta DiMAGE A2 (2004) and Canon 5D Mark III (2012). Eight years is a lot of time in terms of technology, meaning newer sensors are overall much more efficient than the older ones.
Pixel pitch
2.7 µm
6.22 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 3.52 µm (130%)
Pixel pitch of 5D Mark III is approx. 130% higher than pixel pitch of DiMAGE A2.
Pixel area
7.29 µm²
38.69 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 31.4 µm² (431%)
A pixel on Canon 5D Mark III sensor is approx. 431% bigger than a pixel on Konica-Minolta DiMAGE A2.
Pixel density
13.74 MP/cm²
2.58 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 11.16 µm (433%)
Konica-Minolta DiMAGE A2 has approx. 433% higher pixel density than Canon 5D Mark III.
To learn about the accuracy of these numbers, click here.



Specs

Konica-Minolta DiMAGE A2
Canon 5D Mark III
Crop factor
3.93
1
Total megapixels
23.38
Effective megapixels
22.30
Optical zoom
7.1x
Digital zoom
Yes
No
ISO sensitivity
Auto, 64, 100, 200, 400, 800
Auto, 100 - 25600 in 1/3 stops, plus 50, 51200, 102400 as option
RAW
Manual focus
Normal focus range
50 cm
Macro focus range
13 cm
Focal length (35mm equiv.)
28 - 200 mm
Aperture priority
Yes
Yes
Max. aperture
f2.8 - f3.5
Max. aperture (35mm equiv.)
f11 - f13.8
n/a
Metering
Multi, Center-weighted, Spot, Partial
Exposure compensation
±2 EV (in 1/3 EV steps)
±5 EV (in 1/3 EV, 1/2 EV steps)
Shutter priority
Yes
Yes
Min. shutter speed
30 sec
30 sec
Max. shutter speed
1/4000 sec
1/8000 sec
Built-in flash
External flash
Viewfinder
Electronic
Optical (pentaprism)
White balance presets
6
6
Screen size
1.8"
3.2"
Screen resolution
113,000 dots
1,040,000 dots
Video capture
Max. video resolution
1920x1080 (30p/25p/24p)
Storage types
Compact Flash (Type I or II)
Compact Flash Type I (UDMA compatible), SD/SDHC/SDXC
USB
USB 1.0
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
AA (4) batteries (NiMH recommended)
Lithium-Ion LP-E6 rechargeable battery
Weight
639 g
950 g
Dimensions
117 x 85 x 114 mm
152 x 116 x 76 mm
Year
2004
2012




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Konica-Minolta DiMAGE A2 diagonal

The diagonal of DiMAGE A2 sensor is not 2/3 or 0.67" (16.9 mm) as you might expect, but approximately two thirds of that value - 11 mm. If you want to know why, see sensor sizes.

w = 8.80 mm
h = 6.60 mm
Diagonal =  8.80² + 6.60²   = 11.00 mm

Canon 5D Mark III diagonal

w = 36.00 mm
h = 24.00 mm
Diagonal =  36.00² + 24.00²   = 43.27 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

DiMAGE A2 sensor area

Width = 8.80 mm
Height = 6.60 mm

Surface area = 8.80 × 6.60 = 58.08 mm²

5D Mark III sensor area

Width = 36.00 mm
Height = 24.00 mm

Surface area = 36.00 × 24.00 = 864.00 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

DiMAGE A2 pixel pitch

Sensor width = 8.80 mm
Sensor resolution width = 3262 pixels
Pixel pitch =   8.80  × 1000  = 2.7 µm
3262

5D Mark III pixel pitch

Sensor width = 36.00 mm
Sensor resolution width = 5784 pixels
Pixel pitch =   36.00  × 1000  = 6.22 µm
5784


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

DiMAGE A2 pixel area

Pixel pitch = 2.7 µm

Pixel area = 2.7² = 7.29 µm²

5D Mark III pixel area

Pixel pitch = 6.22 µm

Pixel area = 6.22² = 38.69 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

DiMAGE A2 pixel density

Sensor resolution width = 3262 pixels
Sensor width = 0.88 cm

Pixel density = (3262 / 0.88)² / 1000000 = 13.74 MP/cm²

5D Mark III pixel density

Sensor resolution width = 5784 pixels
Sensor width = 3.6 cm

Pixel density = (5784 / 3.6)² / 1000000 = 2.58 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

DiMAGE A2 sensor resolution

Sensor width = 8.80 mm
Sensor height = 6.60 mm
Effective megapixels = 8.00
r = 8.80/6.60 = 1.33
X =  8.00 × 1000000  = 2453
1.33
Resolution horizontal: X × r = 2453 × 1.33 = 3262
Resolution vertical: X = 2453

Sensor resolution = 3262 x 2453

5D Mark III sensor resolution

Sensor width = 36.00 mm
Sensor height = 24.00 mm
Effective megapixels = 22.30
r = 36.00/24.00 = 1.5
X =  22.30 × 1000000  = 3856
1.5
Resolution horizontal: X × r = 3856 × 1.5 = 5784
Resolution vertical: X = 3856

Sensor resolution = 5784 x 3856


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


DiMAGE A2 crop factor

Sensor diagonal in mm = 11.00 mm
Crop factor =   43.27  = 3.93
11.00

5D Mark III crop factor

Sensor diagonal in mm = 43.27 mm
Crop factor =   43.27  = 1
43.27

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

DiMAGE A2 equivalent aperture

Crop factor = 3.93
Aperture = f2.8 - f3.5

35-mm equivalent aperture = (f2.8 - f3.5) × 3.93 = f11 - f13.8

5D Mark III equivalent aperture

Aperture is a lens characteristic, so it's calculated only for fixed lens cameras. If you want to know the equivalent aperture for Canon 5D Mark III, take the aperture of the lens you're using and multiply it with crop factor.

Since crop factor for Canon 5D Mark III is 1, the equivalent aperture is aperture.

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.