Konica-Minolta DiMAGE G600 vs. Panasonic Lumix DMC-LX100

Comparison

change cameras »
DiMAGE G600 image
vs
Lumix DMC-LX100 image
Konica-Minolta DiMAGE G600 Panasonic Lumix DMC-LX100
check price » check price »
Megapixels
6.40
12.80
Max. image resolution
2816 x 2112
4112 x 3088

Sensor

Sensor type
CCD
CMOS
Sensor size
1/1.76" (~ 7.27 x 5.46 mm)
Four Thirds (17.3 x 13 mm)
Sensor resolution
2918 x 2194
4126 x 3102
Diagonal
9.09 mm
21.64 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1 : 5.67
(ratio)
Konica-Minolta DiMAGE G600 Panasonic Lumix DMC-LX100
Surface area:
39.69 mm² vs 224.90 mm²
Difference: 185.21 mm² (467%)
LX100 sensor is approx. 5.67x bigger than DiMAGE G600 sensor.
Note: You are comparing sensors of very different generations. There is a gap of 10 years between Konica-Minolta DiMAGE G600 (2004) and Panasonic LX100 (2014). Ten years is a lot of time in terms of technology, meaning newer sensors are overall much more efficient than the older ones.
Pixel pitch
2.49 µm
4.19 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 1.7 µm (68%)
Pixel pitch of LX100 is approx. 68% higher than pixel pitch of DiMAGE G600.
Pixel area
6.2 µm²
17.56 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 11.36 µm² (183%)
A pixel on Panasonic LX100 sensor is approx. 183% bigger than a pixel on Konica-Minolta DiMAGE G600.
Pixel density
16.11 MP/cm²
5.69 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 10.42 µm (183%)
Konica-Minolta DiMAGE G600 has approx. 183% higher pixel density than Panasonic LX100.
To learn about the accuracy of these numbers, click here.



Specs

Konica-Minolta DiMAGE G600
Panasonic LX100
Crop factor
4.76
2
Total megapixels
16.84
Effective megapixels
12.80
Optical zoom
3x
3.1x
Digital zoom
Yes
Yes
ISO sensitivity
Auto, 50, 100, 200, 400
Auto, 100 (extended), 200, 400, 800, 1600, 3200, 6400, 12800, 25600
RAW
Manual focus
Normal focus range
50 cm
50 cm
Macro focus range
6 cm
3 cm
Focal length (35mm equiv.)
39 - 117 mm
24 - 75 mm
Aperture priority
No
Yes
Max. aperture
f2.8 - f4.9
f1.7 - f2.8
Max. aperture (35mm equiv.)
f13.3 - f23.3
f3.4 - f5.6
Metering
Centre weighted, Spot
Multi, Center-weighted, Spot
Exposure compensation
±1.5 EV (in 1/3 EV steps)
±3 EV (in 1/3 EV steps)
Shutter priority
No
Yes
Min. shutter speed
15 sec
60 sec
Max. shutter speed
1/2000 sec
1/16000 sec
Built-in flash
External flash
Viewfinder
Optical (tunnel)
Electronic
White balance presets
5
5
Screen size
1.5"
3"
Screen resolution
118,000 dots
921,600 dots
Video capture
Max. video resolution
3840x2160 (30p/24p)
Storage types
MultiMedia, Secure Digital
SD/SDHC/SDXC
USB
USB 1.0
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
Lithium-Ion rechargeable
Li-ion Battery Pack
Weight
195 g
393 g
Dimensions
94 x 56 x 30 mm
114.8 x 66.2 x 55 mm
Year
2004
2014




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Konica-Minolta DiMAGE G600 diagonal

The diagonal of DiMAGE G600 sensor is not 1/1.76 or 0.57" (14.4 mm) as you might expect, but approximately two thirds of that value - 9.09 mm. If you want to know why, see sensor sizes.

w = 7.27 mm
h = 5.46 mm
Diagonal =  7.27² + 5.46²   = 9.09 mm

Panasonic LX100 diagonal

w = 17.30 mm
h = 13.00 mm
Diagonal =  17.30² + 13.00²   = 21.64 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

DiMAGE G600 sensor area

Width = 7.27 mm
Height = 5.46 mm

Surface area = 7.27 × 5.46 = 39.69 mm²

LX100 sensor area

Width = 17.30 mm
Height = 13.00 mm

Surface area = 17.30 × 13.00 = 224.90 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

DiMAGE G600 pixel pitch

Sensor width = 7.27 mm
Sensor resolution width = 2918 pixels
Pixel pitch =   7.27  × 1000  = 2.49 µm
2918

LX100 pixel pitch

Sensor width = 17.30 mm
Sensor resolution width = 4126 pixels
Pixel pitch =   17.30  × 1000  = 4.19 µm
4126


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

DiMAGE G600 pixel area

Pixel pitch = 2.49 µm

Pixel area = 2.49² = 6.2 µm²

LX100 pixel area

Pixel pitch = 4.19 µm

Pixel area = 4.19² = 17.56 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

DiMAGE G600 pixel density

Sensor resolution width = 2918 pixels
Sensor width = 0.727 cm

Pixel density = (2918 / 0.727)² / 1000000 = 16.11 MP/cm²

LX100 pixel density

Sensor resolution width = 4126 pixels
Sensor width = 1.73 cm

Pixel density = (4126 / 1.73)² / 1000000 = 5.69 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

DiMAGE G600 sensor resolution

Sensor width = 7.27 mm
Sensor height = 5.46 mm
Effective megapixels = 6.40
r = 7.27/5.46 = 1.33
X =  6.40 × 1000000  = 2194
1.33
Resolution horizontal: X × r = 2194 × 1.33 = 2918
Resolution vertical: X = 2194

Sensor resolution = 2918 x 2194

LX100 sensor resolution

Sensor width = 17.30 mm
Sensor height = 13.00 mm
Effective megapixels = 12.80
r = 17.30/13.00 = 1.33
X =  12.80 × 1000000  = 3102
1.33
Resolution horizontal: X × r = 3102 × 1.33 = 4126
Resolution vertical: X = 3102

Sensor resolution = 4126 x 3102


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


DiMAGE G600 crop factor

Sensor diagonal in mm = 9.09 mm
Crop factor =   43.27  = 4.76
9.09

LX100 crop factor

Sensor diagonal in mm = 21.64 mm
Crop factor =   43.27  = 2
21.64

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

DiMAGE G600 equivalent aperture

Crop factor = 4.76
Aperture = f2.8 - f4.9

35-mm equivalent aperture = (f2.8 - f4.9) × 4.76 = f13.3 - f23.3

LX100 equivalent aperture

Crop factor = 2
Aperture = f1.7 - f2.8

35-mm equivalent aperture = (f1.7 - f2.8) × 2 = f3.4 - f5.6

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.