Konica-Minolta DiMAGE Z6 vs. Olympus C-730 UZ

Comparison

change cameras »
DiMAGE Z6 image
vs
C-730 UZ image
Konica-Minolta DiMAGE Z6 Olympus C-730 UZ
check price » check price »
Megapixels
6.40
3.00
Max. image resolution
2816 x 2112
2048 x 1536

Sensor

Sensor type
CCD
CCD
Sensor size
1/2.5" (~ 5.75 x 4.32 mm)
1/2.7" (~ 5.33 x 4 mm)
Sensor resolution
2918 x 2194
1998 x 1502
Diagonal
7.19 mm
6.66 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1.17 : 1
(ratio)
Konica-Minolta DiMAGE Z6 Olympus C-730 UZ
Surface area:
24.84 mm² vs 21.32 mm²
Difference: 3.52 mm² (17%)
DiMAGE Z6 sensor is approx. 1.17x bigger than C-730 UZ sensor.
Note: You are comparing cameras of different generations. There is a 3 year gap between Konica-Minolta DiMAGE Z6 (2005) and Olympus C-730 UZ (2002). All things being equal, newer sensor generations generally outperform the older.
Pixel pitch
1.97 µm
2.67 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 0.7 µm (36%)
Pixel pitch of C-730 UZ is approx. 36% higher than pixel pitch of DiMAGE Z6.
Pixel area
3.88 µm²
7.13 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 3.25 µm² (84%)
A pixel on Olympus C-730 UZ sensor is approx. 84% bigger than a pixel on Konica-Minolta DiMAGE Z6.
Pixel density
25.75 MP/cm²
14.05 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 11.7 µm (83%)
Konica-Minolta DiMAGE Z6 has approx. 83% higher pixel density than Olympus C-730 UZ.
To learn about the accuracy of these numbers, click here.



Specs

Konica-Minolta DiMAGE Z6
Olympus C-730 UZ
Crop factor
6.02
6.5
Total megapixels
3.30
Effective megapixels
3.00
Optical zoom
12x
10x
Digital zoom
Yes
Yes
ISO sensitivity
Auto, 50, 100, 200, 320
Auto, 100, 200, 400
RAW
Manual focus
Normal focus range
60 cm
60 cm
Macro focus range
1 cm
10 cm
Focal length (35mm equiv.)
35 - 420 mm
38 - 380 mm
Aperture priority
Yes
Yes
Max. aperture
f2.8 - f4.5
f2.8 - f3.5
Max. aperture (35mm equiv.)
f16.9 - f27.1
f18.2 - f22.8
Metering
Centre weighted, Multi-segment, Spot
ESP Digital, Multi Spot, Spot
Exposure compensation
±2 EV (in 1/3 EV steps)
±2 EV (in 1/3 EV steps)
Shutter priority
Yes
Yes
Min. shutter speed
15 sec
16 sec
Max. shutter speed
1/1000 sec
1/1000 sec
Built-in flash
External flash
Viewfinder
Electronic
Electronic
White balance presets
7
7
Screen size
2"
1.5"
Screen resolution
114,000 dots
114,000 dots
Video capture
Max. video resolution
Storage types
Secure Digital
SmartMedia, xD Picture card
USB
USB 1.0
USB 1.0
HDMI
Wireless
GPS
Battery
AA (4) batteries (NiMH recommended)
AA (4) batteries (NiMH recommended)
Weight
340 g
397 g
Dimensions
109 x 80 x 84 mm
108 x 76 x 78 mm
Year
2005
2002




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Konica-Minolta DiMAGE Z6 diagonal

The diagonal of DiMAGE Z6 sensor is not 1/2.5 or 0.4" (10.2 mm) as you might expect, but approximately two thirds of that value - 7.19 mm. If you want to know why, see sensor sizes.

w = 5.75 mm
h = 4.32 mm
Diagonal =  5.75² + 4.32²   = 7.19 mm

Olympus C-730 UZ diagonal

The diagonal of C-730 UZ sensor is not 1/2.7 or 0.37" (9.4 mm) as you might expect, but approximately two thirds of that value - 6.66 mm. If you want to know why, see sensor sizes.

w = 5.33 mm
h = 4.00 mm
Diagonal =  5.33² + 4.00²   = 6.66 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

DiMAGE Z6 sensor area

Width = 5.75 mm
Height = 4.32 mm

Surface area = 5.75 × 4.32 = 24.84 mm²

C-730 UZ sensor area

Width = 5.33 mm
Height = 4.00 mm

Surface area = 5.33 × 4.00 = 21.32 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

DiMAGE Z6 pixel pitch

Sensor width = 5.75 mm
Sensor resolution width = 2918 pixels
Pixel pitch =   5.75  × 1000  = 1.97 µm
2918

C-730 UZ pixel pitch

Sensor width = 5.33 mm
Sensor resolution width = 1998 pixels
Pixel pitch =   5.33  × 1000  = 2.67 µm
1998


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

DiMAGE Z6 pixel area

Pixel pitch = 1.97 µm

Pixel area = 1.97² = 3.88 µm²

C-730 UZ pixel area

Pixel pitch = 2.67 µm

Pixel area = 2.67² = 7.13 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

DiMAGE Z6 pixel density

Sensor resolution width = 2918 pixels
Sensor width = 0.575 cm

Pixel density = (2918 / 0.575)² / 1000000 = 25.75 MP/cm²

C-730 UZ pixel density

Sensor resolution width = 1998 pixels
Sensor width = 0.533 cm

Pixel density = (1998 / 0.533)² / 1000000 = 14.05 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

DiMAGE Z6 sensor resolution

Sensor width = 5.75 mm
Sensor height = 4.32 mm
Effective megapixels = 6.40
r = 5.75/4.32 = 1.33
X =  6.40 × 1000000  = 2194
1.33
Resolution horizontal: X × r = 2194 × 1.33 = 2918
Resolution vertical: X = 2194

Sensor resolution = 2918 x 2194

C-730 UZ sensor resolution

Sensor width = 5.33 mm
Sensor height = 4.00 mm
Effective megapixels = 3.00
r = 5.33/4.00 = 1.33
X =  3.00 × 1000000  = 1502
1.33
Resolution horizontal: X × r = 1502 × 1.33 = 1998
Resolution vertical: X = 1502

Sensor resolution = 1998 x 1502


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


DiMAGE Z6 crop factor

Sensor diagonal in mm = 7.19 mm
Crop factor =   43.27  = 6.02
7.19

C-730 UZ crop factor

Sensor diagonal in mm = 6.66 mm
Crop factor =   43.27  = 6.5
6.66

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

DiMAGE Z6 equivalent aperture

Crop factor = 6.02
Aperture = f2.8 - f4.5

35-mm equivalent aperture = (f2.8 - f4.5) × 6.02 = f16.9 - f27.1

C-730 UZ equivalent aperture

Crop factor = 6.5
Aperture = f2.8 - f3.5

35-mm equivalent aperture = (f2.8 - f3.5) × 6.5 = f18.2 - f22.8

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.