Leica S (Type 007) vs. Pentax 645D

Comparison

change cameras »
S (Type 007) image
vs
645D image
Leica S (Type 007) Pentax 645D
check price » check price »
Megapixels
37.50
40.00
Max. image resolution
7500 x 5000
7264 x 5440

Sensor

Sensor type
CMOS
CCD
Sensor size
45 x 30 mm
44 x 33 mm
Sensor resolution
7500 x 5000
7294 x 5484
Diagonal
54.08 mm
55.00 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1 : 1.08
(ratio)
Leica S (Type 007) Pentax 645D
Surface area:
1350.00 mm² vs 1452.00 mm²
Difference: 102 mm² (8%)
645D sensor is approx. 1.08x bigger than S (Type 007) sensor.
Note: You are comparing cameras of different generations. There is a 4 year gap between Leica S (Type 007) (2014) and Pentax 645D (2010). All things being equal, newer sensor generations generally outperform the older.
Pixel pitch
6 µm
6.03 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 0.03 µm (0.5%)
Pixel pitch of 645D is approx. 0.5% higher than pixel pitch of S (Type 007).
Pixel area
36 µm²
36.36 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 0.36 µm² (1%)
A pixel on Pentax 645D sensor is approx. 1% bigger than a pixel on Leica S (Type 007).
Pixel density
2.78 MP/cm²
2.75 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 0.03 µm (1%)
Leica S (Type 007) has approx. 1% higher pixel density than Pentax 645D.
To learn about the accuracy of these numbers, click here.



Specs

Leica S (Type 007)
Pentax 645D
Crop factor
0.8
0.79
Total megapixels
40.10
Effective megapixels
37.50
40.00
Optical zoom
Digital zoom
No
No
ISO sensitivity
Auto, 100, 200, 400, 800, 1600, 3200, 6400
Auto, 200 - 1600
RAW
Manual focus
Normal focus range
Macro focus range
Focal length (35mm equiv.)
Aperture priority
Yes
Yes
Max. aperture
Max. aperture (35mm equiv.)
n/a
n/a
Metering
Multi, Center-weighted, Spot
Centre weighted, Multi-segment, Spot
Exposure compensation
±3 EV (in 1/3 EV steps)
±5 EV (in 1/3 EV, 1/2 EV, 1 EV steps)
Shutter priority
Yes
Yes
Min. shutter speed
125 sec
30 sec
Max. shutter speed
1/4000 sec
1/4000 sec
Built-in flash
External flash
Viewfinder
Optical (pentaprism)
Optical (pentaprism)
White balance presets
12
8
Screen size
3"
3"
Screen resolution
921,600 dots
921,000 dots
Video capture
Max. video resolution
4096x2160 (24p)
Storage types
SD/SDHC/SDXC/CompactFlash
SDHC, Secure Digital
USB
USB 3.0 (5 GBit/sec)
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
Rechargeable lithium-ion battery
Lithium-Ion D-LI90 rechargeable battery
Weight
1260 g
1400 g
Dimensions
160 x 120 x 80 mm
156 x 117 x 119 mm
Year
2014
2010




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Leica S (Type 007) diagonal

w = 45.00 mm
h = 30.00 mm
Diagonal =  45.00² + 30.00²   = 54.08 mm

Pentax 645D diagonal

w = 44.00 mm
h = 33.00 mm
Diagonal =  44.00² + 33.00²   = 55.00 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

S (Type 007) sensor area

Width = 45.00 mm
Height = 30.00 mm

Surface area = 45.00 × 30.00 = 1350.00 mm²

645D sensor area

Width = 44.00 mm
Height = 33.00 mm

Surface area = 44.00 × 33.00 = 1452.00 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

S (Type 007) pixel pitch

Sensor width = 45.00 mm
Sensor resolution width = 7500 pixels
Pixel pitch =   45.00  × 1000  = 6 µm
7500

645D pixel pitch

Sensor width = 44.00 mm
Sensor resolution width = 7294 pixels
Pixel pitch =   44.00  × 1000  = 6.03 µm
7294


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

S (Type 007) pixel area

Pixel pitch = 6 µm

Pixel area = 6² = 36 µm²

645D pixel area

Pixel pitch = 6.03 µm

Pixel area = 6.03² = 36.36 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

S (Type 007) pixel density

Sensor resolution width = 7500 pixels
Sensor width = 4.5 cm

Pixel density = (7500 / 4.5)² / 1000000 = 2.78 MP/cm²

645D pixel density

Sensor resolution width = 7294 pixels
Sensor width = 4.4 cm

Pixel density = (7294 / 4.4)² / 1000000 = 2.75 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

S (Type 007) sensor resolution

Sensor width = 45.00 mm
Sensor height = 30.00 mm
Effective megapixels = 37.50
r = 45.00/30.00 = 1.5
X =  37.50 × 1000000  = 5000
1.5
Resolution horizontal: X × r = 5000 × 1.5 = 7500
Resolution vertical: X = 5000

Sensor resolution = 7500 x 5000

645D sensor resolution

Sensor width = 44.00 mm
Sensor height = 33.00 mm
Effective megapixels = 40.00
r = 44.00/33.00 = 1.33
X =  40.00 × 1000000  = 5484
1.33
Resolution horizontal: X × r = 5484 × 1.33 = 7294
Resolution vertical: X = 5484

Sensor resolution = 7294 x 5484


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


S (Type 007) crop factor

Sensor diagonal in mm = 54.08 mm
Crop factor =   43.27  = 0.8
54.08

645D crop factor

Sensor diagonal in mm = 55.00 mm
Crop factor =   43.27  = 0.79
55.00

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

S (Type 007) equivalent aperture

Aperture is a lens characteristic, so it's calculated only for fixed lens cameras. If you want to know the equivalent aperture for Leica S (Type 007), take the aperture of the lens you're using and multiply it with crop factor.

Crop factor for Leica S (Type 007) is 0.8

645D equivalent aperture

Aperture is a lens characteristic, so it's calculated only for fixed lens cameras. If you want to know the equivalent aperture for Pentax 645D, take the aperture of the lens you're using and multiply it with crop factor.

Crop factor for Pentax 645D is 0.79

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.