Panasonic Lumix DMC-LC33 vs. Canon PowerShot SX260 HS

Comparison

change cameras »
Lumix DMC-LC33 image
vs
PowerShot SX260 HS image
Panasonic Lumix DMC-LC33 Canon PowerShot SX260 HS
check price » check price »
Megapixels
3.10
12.10
Max. image resolution
2048 x 1536
4000 x 3000

Sensor

Sensor type
CCD
CMOS
Sensor size
1/2.5" (~ 5.75 x 4.32 mm)
1/2.3" (~ 6.16 x 4.62 mm)
Sensor resolution
2031 x 1527
4011 x 3016
Diagonal
7.19 mm
7.70 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1 : 1.15
(ratio)
Panasonic Lumix DMC-LC33 Canon PowerShot SX260 HS
Surface area:
24.84 mm² vs 28.46 mm²
Difference: 3.62 mm² (15%)
SX260 HS sensor is approx. 1.15x bigger than LC33 sensor.
Note: You are comparing sensors of very different generations. There is a gap of 9 years between Panasonic LC33 (2003) and Canon SX260 HS (2012). Nine years is a lot of time in terms of technology, meaning newer sensors are overall much more efficient than the older ones.
Pixel pitch
2.83 µm
1.54 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 1.29 µm (84%)
Pixel pitch of LC33 is approx. 84% higher than pixel pitch of SX260 HS.
Pixel area
8.01 µm²
2.37 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 5.64 µm² (238%)
A pixel on Panasonic LC33 sensor is approx. 238% bigger than a pixel on Canon SX260 HS.
Pixel density
12.48 MP/cm²
42.4 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 29.92 µm (240%)
Canon SX260 HS has approx. 240% higher pixel density than Panasonic LC33.
To learn about the accuracy of these numbers, click here.



Specs

Panasonic LC33
Canon SX260 HS
Crop factor
6.02
5.62
Total megapixels
3.30
Effective megapixels
3.10
12.10
Optical zoom
3x
20x
Digital zoom
Yes
Yes
ISO sensitivity
Auto, 50, 100, 200, 400
Auto, 100, 200, 400, 800, 1600, 3200
RAW
Manual focus
Normal focus range
50 cm
45 cm
Macro focus range
10 cm
5 cm
Focal length (35mm equiv.)
35 - 105 mm
25 - 500 mm
Aperture priority
No
Yes
Max. aperture
f2.8 - f4.9
f3.5 - f6.8
Max. aperture (35mm equiv.)
f16.9 - f29.5
f19.7 - f38.2
Metering
Matrix, Spot
Centre weighted, Evaluative, Spot
Exposure compensation
±2 EV (in 1/3 EV steps)
±2 EV (in 1/3 EV steps)
Shutter priority
No
Yes
Min. shutter speed
8 sec
15 sec
Max. shutter speed
1/2000 sec
1/3200 sec
Built-in flash
External flash
Viewfinder
Optical (tunnel)
None
White balance presets
7
6
Screen size
1.5"
3"
Screen resolution
114,000 dots
461,000 dots
Video capture
Max. video resolution
1920x1080 (24p)
Storage types
MultiMedia, Secure Digital
SDHC, SDXC, Secure Digital
USB
USB 1.0
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
AA (2) batteries (NiMH recommended)
Lithium-Ion NB-6L rechargeable battery
Weight
215 g
231 g
Dimensions
96 x 66 x 34 mm
105.5 x 61.0 x 32.7 mm
Year
2003
2012




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Panasonic LC33 diagonal

The diagonal of LC33 sensor is not 1/2.5 or 0.4" (10.2 mm) as you might expect, but approximately two thirds of that value - 7.19 mm. If you want to know why, see sensor sizes.

w = 5.75 mm
h = 4.32 mm
Diagonal =  5.75² + 4.32²   = 7.19 mm

Canon SX260 HS diagonal

The diagonal of SX260 HS sensor is not 1/2.3 or 0.43" (11 mm) as you might expect, but approximately two thirds of that value - 7.7 mm. If you want to know why, see sensor sizes.

w = 6.16 mm
h = 4.62 mm
Diagonal =  6.16² + 4.62²   = 7.70 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

LC33 sensor area

Width = 5.75 mm
Height = 4.32 mm

Surface area = 5.75 × 4.32 = 24.84 mm²

SX260 HS sensor area

Width = 6.16 mm
Height = 4.62 mm

Surface area = 6.16 × 4.62 = 28.46 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

LC33 pixel pitch

Sensor width = 5.75 mm
Sensor resolution width = 2031 pixels
Pixel pitch =   5.75  × 1000  = 2.83 µm
2031

SX260 HS pixel pitch

Sensor width = 6.16 mm
Sensor resolution width = 4011 pixels
Pixel pitch =   6.16  × 1000  = 1.54 µm
4011


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

LC33 pixel area

Pixel pitch = 2.83 µm

Pixel area = 2.83² = 8.01 µm²

SX260 HS pixel area

Pixel pitch = 1.54 µm

Pixel area = 1.54² = 2.37 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

LC33 pixel density

Sensor resolution width = 2031 pixels
Sensor width = 0.575 cm

Pixel density = (2031 / 0.575)² / 1000000 = 12.48 MP/cm²

SX260 HS pixel density

Sensor resolution width = 4011 pixels
Sensor width = 0.616 cm

Pixel density = (4011 / 0.616)² / 1000000 = 42.4 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

LC33 sensor resolution

Sensor width = 5.75 mm
Sensor height = 4.32 mm
Effective megapixels = 3.10
r = 5.75/4.32 = 1.33
X =  3.10 × 1000000  = 1527
1.33
Resolution horizontal: X × r = 1527 × 1.33 = 2031
Resolution vertical: X = 1527

Sensor resolution = 2031 x 1527

SX260 HS sensor resolution

Sensor width = 6.16 mm
Sensor height = 4.62 mm
Effective megapixels = 12.10
r = 6.16/4.62 = 1.33
X =  12.10 × 1000000  = 3016
1.33
Resolution horizontal: X × r = 3016 × 1.33 = 4011
Resolution vertical: X = 3016

Sensor resolution = 4011 x 3016


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


LC33 crop factor

Sensor diagonal in mm = 7.19 mm
Crop factor =   43.27  = 6.02
7.19

SX260 HS crop factor

Sensor diagonal in mm = 7.70 mm
Crop factor =   43.27  = 5.62
7.70

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

LC33 equivalent aperture

Crop factor = 6.02
Aperture = f2.8 - f4.9

35-mm equivalent aperture = (f2.8 - f4.9) × 6.02 = f16.9 - f29.5

SX260 HS equivalent aperture

Crop factor = 5.62
Aperture = f3.5 - f6.8

35-mm equivalent aperture = (f3.5 - f6.8) × 5.62 = f19.7 - f38.2

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.