Panasonic Lumix DMC-ZS45 vs. Panasonic Lumix DMC-ZS10

Comparison

change cameras »
Lumix DMC-ZS45 image
vs
Lumix DMC-ZS10 image
Panasonic Lumix DMC-ZS45 Panasonic Lumix DMC-ZS10
check price » check price »
Megapixels
16.00
14.10
Max. image resolution
4608 x 3456
4320 x 3240

Sensor

Sensor type
CMOS
CMOS
Sensor size
1/2.33" (~ 6.08 x 4.56 mm)
1/2.33" (~ 6.08 x 4.56 mm)
Sensor resolution
4612 x 3468
4330 x 3256
Diagonal
7.60 mm
7.60 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1 : 1
(ratio)
Panasonic Lumix DMC-ZS45 Panasonic Lumix DMC-ZS10
Surface area:
27.72 mm² vs 27.72 mm²
Difference: 0 mm² (0%)
ZS45 and ZS10 sensors are the same size.
Note: You are comparing cameras of different generations. There is a 4 year gap between Panasonic ZS45 (2015) and Panasonic ZS10 (2011). All things being equal, newer sensor generations generally outperform the older.
Pixel pitch
1.32 µm
1.4 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 0.08 µm (6%)
Pixel pitch of ZS10 is approx. 6% higher than pixel pitch of ZS45.
Pixel area
1.74 µm²
1.96 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 0.22 µm² (13%)
A pixel on Panasonic ZS10 sensor is approx. 13% bigger than a pixel on Panasonic ZS45.
Pixel density
57.54 MP/cm²
50.72 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 6.82 µm (13%)
Panasonic ZS45 has approx. 13% higher pixel density than Panasonic ZS10.
To learn about the accuracy of these numbers, click here.



Specs

Panasonic ZS45
Panasonic ZS10
Crop factor
5.69
5.69
Total megapixels
17.50
15.10
Effective megapixels
16.00
14.10
Optical zoom
20x
16x
Digital zoom
Yes
Yes
ISO sensitivity
Auto, 100, 200, 400, 800, 1600, 3200 (High Sensitivity Mode 1600 - 6400)
Auto, 100, 200, 400, 800, 1600 - 6400
RAW
Manual focus
Normal focus range
50 cm
50 cm
Macro focus range
3 cm
3 cm
Focal length (35mm equiv.)
24 - 480 mm
24 - 384 mm
Aperture priority
Yes
Yes
Max. aperture
f3.3 - f6.4
f3.3 - f5.9
Max. aperture (35mm equiv.)
f18.8 - f36.4
f18.8 - f33.6
Metering
Multi, Center-weighted, Spot
Centre weighted, Intelligent Multiple, Spot
Exposure compensation
±2 EV (in 1/3 EV steps)
±2 EV (in 1/3 EV steps)
Shutter priority
Yes
Yes
Min. shutter speed
4 sec
60 sec
Max. shutter speed
1/2000 sec
1/4000 sec
Built-in flash
External flash
Viewfinder
None
None
White balance presets
4
6
Screen size
3"
3"
Screen resolution
1,040,000 dots
460,000 dots
Video capture
Max. video resolution
1920x1080 (30p)
Storage types
SD/SDHC/SDXC
SDHC, SDXC, Secure Digital
USB
USB 2.0 (480 Mbit/sec)
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
Li-ion Battery Pack
Lithium-Ion rechargeable battery
Weight
248 g
219 g
Dimensions
107.9 x 59.9 x 32.1 mm
105 x 58 x 33 mm
Year
2015
2011




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Panasonic ZS45 diagonal

The diagonal of ZS45 sensor is not 1/2.33 or 0.43" (10.9 mm) as you might expect, but approximately two thirds of that value - 7.6 mm. If you want to know why, see sensor sizes.

w = 6.08 mm
h = 4.56 mm
Diagonal =  6.08² + 4.56²   = 7.60 mm

Panasonic ZS10 diagonal

The diagonal of ZS10 sensor is not 1/2.33 or 0.43" (10.9 mm) as you might expect, but approximately two thirds of that value - 7.6 mm. If you want to know why, see sensor sizes.

w = 6.08 mm
h = 4.56 mm
Diagonal =  6.08² + 4.56²   = 7.60 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

ZS45 sensor area

Width = 6.08 mm
Height = 4.56 mm

Surface area = 6.08 × 4.56 = 27.72 mm²

ZS10 sensor area

Width = 6.08 mm
Height = 4.56 mm

Surface area = 6.08 × 4.56 = 27.72 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

ZS45 pixel pitch

Sensor width = 6.08 mm
Sensor resolution width = 4612 pixels
Pixel pitch =   6.08  × 1000  = 1.32 µm
4612

ZS10 pixel pitch

Sensor width = 6.08 mm
Sensor resolution width = 4330 pixels
Pixel pitch =   6.08  × 1000  = 1.4 µm
4330


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

ZS45 pixel area

Pixel pitch = 1.32 µm

Pixel area = 1.32² = 1.74 µm²

ZS10 pixel area

Pixel pitch = 1.4 µm

Pixel area = 1.4² = 1.96 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

ZS45 pixel density

Sensor resolution width = 4612 pixels
Sensor width = 0.608 cm

Pixel density = (4612 / 0.608)² / 1000000 = 57.54 MP/cm²

ZS10 pixel density

Sensor resolution width = 4330 pixels
Sensor width = 0.608 cm

Pixel density = (4330 / 0.608)² / 1000000 = 50.72 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

ZS45 sensor resolution

Sensor width = 6.08 mm
Sensor height = 4.56 mm
Effective megapixels = 16.00
r = 6.08/4.56 = 1.33
X =  16.00 × 1000000  = 3468
1.33
Resolution horizontal: X × r = 3468 × 1.33 = 4612
Resolution vertical: X = 3468

Sensor resolution = 4612 x 3468

ZS10 sensor resolution

Sensor width = 6.08 mm
Sensor height = 4.56 mm
Effective megapixels = 14.10
r = 6.08/4.56 = 1.33
X =  14.10 × 1000000  = 3256
1.33
Resolution horizontal: X × r = 3256 × 1.33 = 4330
Resolution vertical: X = 3256

Sensor resolution = 4330 x 3256


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


ZS45 crop factor

Sensor diagonal in mm = 7.60 mm
Crop factor =   43.27  = 5.69
7.60

ZS10 crop factor

Sensor diagonal in mm = 7.60 mm
Crop factor =   43.27  = 5.69
7.60

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

ZS45 equivalent aperture

Crop factor = 5.69
Aperture = f3.3 - f6.4

35-mm equivalent aperture = (f3.3 - f6.4) × 5.69 = f18.8 - f36.4

ZS10 equivalent aperture

Crop factor = 5.69
Aperture = f3.3 - f5.9

35-mm equivalent aperture = (f3.3 - f5.9) × 5.69 = f18.8 - f33.6

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.