Ricoh GR III vs. Pentax K-1 Mark II

Comparison

change cameras »
GR III image
vs
K-1 Mark II image
Ricoh GR III Pentax K-1 Mark II
check price » check price »
Megapixels
24.24
36.40
Max. image resolution
6000 x 4000
7360 x 4912

Sensor

Sensor type
CMOS
CMOS
Sensor size
23.5 x 15.6 mm
35.9 x 24 mm
Sensor resolution
6051 x 4007
7389 x 4926
Diagonal
28.21 mm
43.18 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1 : 2.35
(ratio)
Ricoh GR III Pentax K-1 Mark II
Surface area:
366.60 mm² vs 861.60 mm²
Difference: 495 mm² (135%)
K-1 Mark II sensor is approx. 2.35x bigger than GR III sensor.
Pixel pitch
3.88 µm
4.86 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 0.98 µm (25%)
Pixel pitch of K-1 Mark II is approx. 25% higher than pixel pitch of GR III.
Pixel area
15.05 µm²
23.62 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 8.57 µm² (57%)
A pixel on Pentax K-1 Mark II sensor is approx. 57% bigger than a pixel on Ricoh GR III.
Pixel density
6.63 MP/cm²
4.24 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 2.39 µm (56%)
Ricoh GR III has approx. 56% higher pixel density than Pentax K-1 Mark II.
To learn about the accuracy of these numbers, click here.



Specs

Ricoh GR III
Pentax K-1 Mark II
Crop factor
1.53
1
Total megapixels
36.77
Effective megapixels
24.24
36.40
Optical zoom
1x
Digital zoom
Yes
ISO sensitivity
Auto, 100-102400
Auto, 100-819200
RAW
Manual focus
Normal focus range
10 cm
Macro focus range
6 cm
Focal length (35mm equiv.)
28 mm
Aperture priority
Yes
Yes
Max. aperture
f2.8
Max. aperture (35mm equiv.)
f4.3
n/a
Metering
Multi, Center-weighted, Highlight-weighted, Spot
Multi, Center-weighted, Spot
Exposure compensation
±5 EV (in 1/3 EV steps)
±5 EV (in 1/3 EV, 1/2 EV steps)
Shutter priority
Yes
Yes
Min. shutter speed
30 sec
30 sec
Max. shutter speed
1/4000 sec
1/8000 sec
Built-in flash
External flash
Viewfinder
Optical (optional)
Optical (pentaprism)
White balance presets
8
8
Screen size
3"
3.2"
Screen resolution
1,036,800 dots
1,036,800 dots
Video capture
Max. video resolution
1920x1080 (60p/30p/24p)
1920x1080 (60i/50i/30p/25p/24p)
Storage types
SD/SDHC/SDXC
SD/SDHC/SDXC (UHS-I)
USB
USB 3.0 (5 GBit/sec)
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
DB-110 lithium-ion battery
D-LI90 lithium-ion battery
Weight
257 g
1010 g
Dimensions
109.4 x 61.9 x 33.2 mm
136.5 x 110 x 85.5 mm
Year
2019
2018




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Ricoh GR III diagonal

w = 23.50 mm
h = 15.60 mm
Diagonal =  23.50² + 15.60²   = 28.21 mm

Pentax K-1 Mark II diagonal

w = 35.90 mm
h = 24.00 mm
Diagonal =  35.90² + 24.00²   = 43.18 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

GR III sensor area

Width = 23.50 mm
Height = 15.60 mm

Surface area = 23.50 × 15.60 = 366.60 mm²

K-1 Mark II sensor area

Width = 35.90 mm
Height = 24.00 mm

Surface area = 35.90 × 24.00 = 861.60 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

GR III pixel pitch

Sensor width = 23.50 mm
Sensor resolution width = 6051 pixels
Pixel pitch =   23.50  × 1000  = 3.88 µm
6051

K-1 Mark II pixel pitch

Sensor width = 35.90 mm
Sensor resolution width = 7389 pixels
Pixel pitch =   35.90  × 1000  = 4.86 µm
7389


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

GR III pixel area

Pixel pitch = 3.88 µm

Pixel area = 3.88² = 15.05 µm²

K-1 Mark II pixel area

Pixel pitch = 4.86 µm

Pixel area = 4.86² = 23.62 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

GR III pixel density

Sensor resolution width = 6051 pixels
Sensor width = 2.35 cm

Pixel density = (6051 / 2.35)² / 1000000 = 6.63 MP/cm²

K-1 Mark II pixel density

Sensor resolution width = 7389 pixels
Sensor width = 3.59 cm

Pixel density = (7389 / 3.59)² / 1000000 = 4.24 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

GR III sensor resolution

Sensor width = 23.50 mm
Sensor height = 15.60 mm
Effective megapixels = 24.24
r = 23.50/15.60 = 1.51
X =  24.24 × 1000000  = 4007
1.51
Resolution horizontal: X × r = 4007 × 1.51 = 6051
Resolution vertical: X = 4007

Sensor resolution = 6051 x 4007

K-1 Mark II sensor resolution

Sensor width = 35.90 mm
Sensor height = 24.00 mm
Effective megapixels = 36.40
r = 35.90/24.00 = 1.5
X =  36.40 × 1000000  = 4926
1.5
Resolution horizontal: X × r = 4926 × 1.5 = 7389
Resolution vertical: X = 4926

Sensor resolution = 7389 x 4926


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


GR III crop factor

Sensor diagonal in mm = 28.21 mm
Crop factor =   43.27  = 1.53
28.21

K-1 Mark II crop factor

Sensor diagonal in mm = 43.18 mm
Crop factor =   43.27  = 1
43.18

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

GR III equivalent aperture

Crop factor = 1.53
Aperture = f2.8

35-mm equivalent aperture = (f2.8) × 1.53 = f4.3

K-1 Mark II equivalent aperture

Aperture is a lens characteristic, so it's calculated only for fixed lens cameras. If you want to know the equivalent aperture for Pentax K-1 Mark II, take the aperture of the lens you're using and multiply it with crop factor.

Since crop factor for Pentax K-1 Mark II is 1, the equivalent aperture is aperture.

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.