Sigma DP1 vs. Canon PowerShot S100

Comparison

change cameras »
DP1 image
vs
PowerShot S100 image
Sigma DP1 Canon PowerShot S100
check price » check price »
Megapixels
4.70
12.10
Max. image resolution
2640 x 1760 x 3
4000 x 3000
Note: Sigma DP1 uses Foveon X3 image sensor, which is a new type of sensor that has 3 layers of photoelements stacked together in 1 pixel location. Traditional CCD/CMOS sensors have 1 pixel for 1 color, whereas Foveon sensor captures all 3 colors (blue, green, and red) at every pixel.

Sensor

Sensor type
Foveon
CMOS
Sensor size
20.7 x 13.8 mm
1/1.7" (~ 7.53 x 5.64 mm)
Sensor resolution
2655 x 1770
4027 x 3005
Diagonal
24.88 mm
9.41 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
6.73 : 1
(ratio)
Sigma DP1 Canon PowerShot S100
Surface area:
285.66 mm² vs 42.47 mm²
Difference: 243.19 mm² (573%)
DP1 sensor is approx. 6.73x bigger than S100 sensor.
Note: You are comparing cameras of different generations. There is a 5 year gap between Sigma DP1 (2006) and Canon S100 (2011). All things being equal, newer sensor generations generally outperform the older.
Pixel pitch
7.8 µm
1.87 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 5.93 µm (317%)
Pixel pitch of DP1 is approx. 317% higher than pixel pitch of S100.
Pixel area
60.84 µm²
3.5 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 57.34 µm² (1638%)
A pixel on Sigma DP1 sensor is approx. 1638% bigger than a pixel on Canon S100.
Pixel density
1.65 MP/cm²
28.6 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 26.95 µm (1633%)
Canon S100 has approx. 1633% higher pixel density than Sigma DP1.
To learn about the accuracy of these numbers, click here.



Specs

Sigma DP1
Canon S100
Crop factor
1.74
4.6
Total megapixels
4.70
13.30
Effective megapixels
4.70
12.10
Optical zoom
1x
5x
Digital zoom
No
Yes
ISO sensitivity
Auto, 100, 200, 400, 800
Auto, 80 - 6400
RAW
Manual focus
Normal focus range
30 cm
Macro focus range
3 cm
Focal length (35mm equiv.)
28 mm
24 - 120 mm
Aperture priority
Yes
Yes
Max. aperture
f2.0 - f5.9
Max. aperture (35mm equiv.)
n/a
f9.2 - f27.1
Metering
Centre weighted, Matrix, Multi-segment
Multi, Center-weighted, Spot
Exposure compensation
±3 EV (in 1/3 EV steps)
±3 EV (in 1/3 EV steps)
Shutter priority
Yes
Yes
Min. shutter speed
30 sec
15 sec
Max. shutter speed
1/4000 sec
1/2000 sec
Built-in flash
External flash
Viewfinder
None
None
White balance presets
6
7
Screen size
2.5"
3"
Screen resolution
230,000 dots
461,000 dots
Video capture
Max. video resolution
Storage types
SDHC, Secure Digital
SDHC, SDXC, Secure Digital
USB
USB 1.0
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
Lithium-Ion rechargeable battery
Lithium-Ion NB-5L rechargeable battery
Weight
270 g
198 g
Dimensions
113 x 60 x 50 mm
98.9 x 59.8 x 26.7 mm
Year
2006
2011




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Sigma DP1 diagonal

w = 20.70 mm
h = 13.80 mm
Diagonal =  20.70² + 13.80²   = 24.88 mm

Canon S100 diagonal

The diagonal of S100 sensor is not 1/1.7 or 0.59" (14.9 mm) as you might expect, but approximately two thirds of that value - 9.41 mm. If you want to know why, see sensor sizes.

w = 7.53 mm
h = 5.64 mm
Diagonal =  7.53² + 5.64²   = 9.41 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

DP1 sensor area

Width = 20.70 mm
Height = 13.80 mm

Surface area = 20.70 × 13.80 = 285.66 mm²

S100 sensor area

Width = 7.53 mm
Height = 5.64 mm

Surface area = 7.53 × 5.64 = 42.47 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

DP1 pixel pitch

Sensor width = 20.70 mm
Sensor resolution width = 2655 pixels
Pixel pitch =   20.70  × 1000  = 7.8 µm
2655

S100 pixel pitch

Sensor width = 7.53 mm
Sensor resolution width = 4027 pixels
Pixel pitch =   7.53  × 1000  = 1.87 µm
4027


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

DP1 pixel area

Pixel pitch = 7.8 µm

Pixel area = 7.8² = 60.84 µm²

S100 pixel area

Pixel pitch = 1.87 µm

Pixel area = 1.87² = 3.5 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

DP1 pixel density

Sensor resolution width = 2655 pixels
Sensor width = 2.07 cm

Pixel density = (2655 / 2.07)² / 1000000 = 1.65 MP/cm²

S100 pixel density

Sensor resolution width = 4027 pixels
Sensor width = 0.753 cm

Pixel density = (4027 / 0.753)² / 1000000 = 28.6 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

DP1 sensor resolution

Sensor width = 20.70 mm
Sensor height = 13.80 mm
Effective megapixels = 4.70
r = 20.70/13.80 = 1.5
X =  4.70 × 1000000  = 1770
1.5
Resolution horizontal: X × r = 1770 × 1.5 = 2655
Resolution vertical: X = 1770

Sensor resolution = 2655 x 1770

S100 sensor resolution

Sensor width = 7.53 mm
Sensor height = 5.64 mm
Effective megapixels = 12.10
r = 7.53/5.64 = 1.34
X =  12.10 × 1000000  = 3005
1.34
Resolution horizontal: X × r = 3005 × 1.34 = 4027
Resolution vertical: X = 3005

Sensor resolution = 4027 x 3005


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


DP1 crop factor

Sensor diagonal in mm = 24.88 mm
Crop factor =   43.27  = 1.74
24.88

S100 crop factor

Sensor diagonal in mm = 9.41 mm
Crop factor =   43.27  = 4.6
9.41

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

DP1 equivalent aperture

Aperture is a lens characteristic, so it's calculated only for fixed lens cameras. If you want to know the equivalent aperture for Sigma DP1, take the aperture of the lens you're using and multiply it with crop factor.

Crop factor for Sigma DP1 is 1.74

S100 equivalent aperture

Crop factor = 4.6
Aperture = f2.0 - f5.9

35-mm equivalent aperture = (f2.0 - f5.9) × 4.6 = f9.2 - f27.1

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.