Sony ZV-1F vs. Olympus PEN E-P2
Comparison
change cameras » | |||||
|
vs |
|
|||
Sony ZV-1F | Olympus PEN E-P2 | ||||
check price » | check price » |
Megapixels
20.10
12.30
Max. image resolution
5472 x 3648
4032 x 3024
Sensor
Sensor type
CMOS
CMOS
Sensor size
13.2 x 8.8 mm
Four Thirds (17.3 x 13 mm)
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera.
Sensors can vary greatly in size. As a general rule, the bigger the
sensor, the better the image quality.
Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.
Learn more about sensor sizes »
Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.
Learn more about sensor sizes »
Actual sensor size
Note: Actual size is set to screen → change »
|
vs |
|
1 | : | 1.94 |
(ratio) | ||
Sony ZV-1F | Olympus PEN E-P2 |
Surface area:
116.16 mm² | vs | 224.90 mm² |
Difference: 108.74 mm² (94%)
PEN E-P2 sensor is approx. 1.94x bigger than ZV-1F sensor.
Note: You are comparing sensors of vastly different generations.
There is a gap of 13 years between Sony ZV-1F (2022) and
Olympus PEN E-P2 (2009).
Thirteen years is a huge amount of time,
technology wise, resulting in newer sensor being much more
efficient than the older one.
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.
The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Pixel or photosite area affects how much light per pixel can be gathered.
The larger it is the more light can be collected by a single pixel.
Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 12.56 µm² (218%)
A pixel on Olympus PEN E-P2 sensor is approx. 218% bigger than a pixel on Sony ZV-1F.
Pixel density tells you how many million pixels fit or would fit in one
square cm of the sensor.
Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Higher pixel density means smaller pixels and lower pixel density means larger pixels.
To learn about the accuracy of these numbers,
click here.
Specs
Sony ZV-1F
Olympus PEN E-P2
Total megapixels
13.10
Effective megapixels
20.10
12.30
Optical zoom
Digital zoom
Yes
No
ISO sensitivity
Auto, 125-12800
Auto, (200 - 3200), 100, 200, 400, 800, 1600, 3200, 6400
RAW
Manual focus
Normal focus range
5 cm
Macro focus range
Focal length (35mm equiv.)
20 mm
Aperture priority
Yes
Yes
Max. aperture
f2
Metering
Multi, Center-weighted, Spot
Multi, Center-weighted, Spot
Exposure compensation
±3 EV (in 1/3 EV steps)
±3 EV (in 1/3 EV, 1/2 EV, 1 EV steps)
Shutter priority
Yes
Yes
Min. shutter speed
15 sec
60 sec
Max. shutter speed
1/32000 sec
1/4000 sec
Built-in flash
External flash
Viewfinder
None
Electronic (optional)
White balance presets
9
8
Screen size
3"
3"
Screen resolution
921,600 dots
230,000 dots
Video capture
Max. video resolution
3840x2160 (30p/25p/24p)
Storage types
SD/SDHC/SDXC
SD/SDHC card
USB
USB 2.0 (480 Mbit/sec)
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
NP-BX1 lithium-ion battery
Lithium-Ion BLS-1 rechargeable battery
Weight
256 g
355 g
Dimensions
105.5 x 60 x 46.4 mm
121 x 70 x 36 mm
Year
2022
2009
Choose cameras to compare
Popular comparisons:
- Sony ZV-1F vs. Canon PowerShot SX740 HS
- Sony ZV-1F vs. Sony ZV-E10
- Sony ZV-1F vs. Sony Cyber-shot DSC-HX60
- Sony ZV-1F vs. Sony Alpha a6000
- Sony ZV-1F vs. Sony ZV-1
- Sony ZV-1F vs. Sony Alpha a6400
- Sony ZV-1F vs. Sony Alpha a5100
- Sony ZV-1F vs. Sony Cyber-shot DSC-RX100
- Sony ZV-1F vs. Canon PowerShot G7 X Mark III
- Sony ZV-1F vs. Sony Cyber-shot DSC-RX100 VII
- Sony ZV-1F vs. Panasonic Lumix DMC-TZ80
Diagonal
Diagonal is calculated by the use of Pythagorean theorem:
where w = sensor width and h = sensor height
Diagonal = √ | w² + h² |
Sony ZV-1F diagonal
w = 13.20 mm
h = 8.80 mm
h = 8.80 mm
Diagonal = √ | 13.20² + 8.80² | = 15.86 mm |
Olympus PEN E-P2 diagonal
w = 17.30 mm
h = 13.00 mm
h = 13.00 mm
Diagonal = √ | 17.30² + 13.00² | = 21.64 mm |
Surface area
Surface area is calculated by multiplying the width and the height of a sensor.
ZV-1F sensor area
Width = 13.20 mm
Height = 8.80 mm
Surface area = 13.20 × 8.80 = 116.16 mm²
Height = 8.80 mm
Surface area = 13.20 × 8.80 = 116.16 mm²
PEN E-P2 sensor area
Width = 17.30 mm
Height = 13.00 mm
Surface area = 17.30 × 13.00 = 224.90 mm²
Height = 13.00 mm
Surface area = 17.30 × 13.00 = 224.90 mm²
Pixel pitch
Pixel pitch is the distance from the center of one pixel to the center of the
next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch = | sensor width in mm | × 1000 |
sensor resolution width in pixels |
ZV-1F pixel pitch
Sensor width = 13.20 mm
Sensor resolution width = 5492 pixels
Sensor resolution width = 5492 pixels
Pixel pitch = | 13.20 | × 1000 | = 2.4 µm |
5492 |
PEN E-P2 pixel pitch
Sensor width = 17.30 mm
Sensor resolution width = 4045 pixels
Sensor resolution width = 4045 pixels
Pixel pitch = | 17.30 | × 1000 | = 4.28 µm |
4045 |
Pixel area
The area of one pixel can be calculated by simply squaring the pixel pitch:
You could also divide sensor surface area with effective megapixels:
Pixel area = pixel pitch²
You could also divide sensor surface area with effective megapixels:
Pixel area = | sensor surface area in mm² |
effective megapixels |
ZV-1F pixel area
Pixel pitch = 2.4 µm
Pixel area = 2.4² = 5.76 µm²
Pixel area = 2.4² = 5.76 µm²
PEN E-P2 pixel area
Pixel pitch = 4.28 µm
Pixel area = 4.28² = 18.32 µm²
Pixel area = 4.28² = 18.32 µm²
Pixel density
Pixel density can be calculated with the following formula:
One could also use this formula:
Pixel density = ( | sensor resolution width in pixels | )² / 1000000 |
sensor width in cm |
One could also use this formula:
Pixel density = | effective megapixels × 1000000 | / 10000 |
sensor surface area in mm² |
ZV-1F pixel density
Sensor resolution width = 5492 pixels
Sensor width = 1.32 cm
Pixel density = (5492 / 1.32)² / 1000000 = 17.31 MP/cm²
Sensor width = 1.32 cm
Pixel density = (5492 / 1.32)² / 1000000 = 17.31 MP/cm²
PEN E-P2 pixel density
Sensor resolution width = 4045 pixels
Sensor width = 1.73 cm
Pixel density = (4045 / 1.73)² / 1000000 = 5.47 MP/cm²
Sensor width = 1.73 cm
Pixel density = (4045 / 1.73)² / 1000000 = 5.47 MP/cm²
Sensor resolution
Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher
than maximum (not interpolated) image resolution which is usually stated on camera specifications.
Sensor resolution is used in pixel pitch, pixel area, and pixel density formula.
For sake of simplicity, we're going to calculate it in 3 stages.
1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.
2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
3. To get sensor resolution we then multiply X with the corresponding ratio:
Resolution horizontal: X × r
Resolution vertical: X
1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.
2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000 → |
|
Resolution horizontal: X × r
Resolution vertical: X
ZV-1F sensor resolution
Sensor width = 13.20 mm
Sensor height = 8.80 mm
Effective megapixels = 20.10
Resolution horizontal: X × r = 3661 × 1.5 = 5492
Resolution vertical: X = 3661
Sensor resolution = 5492 x 3661
Sensor height = 8.80 mm
Effective megapixels = 20.10
r = 13.20/8.80 = 1.5 |
|
Resolution vertical: X = 3661
Sensor resolution = 5492 x 3661
PEN E-P2 sensor resolution
Sensor width = 17.30 mm
Sensor height = 13.00 mm
Effective megapixels = 12.30
Resolution horizontal: X × r = 3041 × 1.33 = 4045
Resolution vertical: X = 3041
Sensor resolution = 4045 x 3041
Sensor height = 13.00 mm
Effective megapixels = 12.30
r = 17.30/13.00 = 1.33 |
|
Resolution vertical: X = 3041
Sensor resolution = 4045 x 3041
Crop factor
Crop factor or focal length multiplier is calculated by dividing the diagonal
of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor = | 43.27 mm |
sensor diagonal in mm |
ZV-1F crop factor
Sensor diagonal in mm = 15.86 mm
Crop factor = | 43.27 | = 2.73 |
15.86 |
PEN E-P2 crop factor
Sensor diagonal in mm = 21.64 mm
Crop factor = | 43.27 | = 2 |
21.64 |
35 mm equivalent aperture
Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture
with crop factor (a.k.a. focal length multiplier).
ZV-1F equivalent aperture
Crop factor = 2.73
Aperture = f2
35-mm equivalent aperture = (f2) × 2.73 = f5.5
Aperture = f2
35-mm equivalent aperture = (f2) × 2.73 = f5.5
PEN E-P2 equivalent aperture
Aperture is a lens characteristic, so it's calculated only for
fixed lens cameras. If you want to know the equivalent aperture for
Olympus PEN E-P2, take the aperture of the lens
you're using and multiply it with crop factor.
Crop factor for Olympus PEN E-P2 is 2
Crop factor for Olympus PEN E-P2 is 2
Enter your screen size (diagonal)
My screen size is
inches
Actual size is currently adjusted to screen.
If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.
If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.