Sony ZV-E10 vs. Sony ZV-1

Comparison

change cameras »
ZV-E10 image
vs
ZV-1 image
Sony ZV-E10 Sony ZV-1
check price » check price »
Megapixels
24.20
20.10
Max. image resolution
6000 x 4000
5472 x 3648

Sensor

Sensor type
CMOS
CMOS
Sensor size
23.5 x 15.6 mm
13.2 x 8.8 mm
Sensor resolution
6045 x 4003
5492 x 3661
Diagonal
28.21 mm
15.86 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
3.16 : 1
(ratio)
Sony ZV-E10 Sony ZV-1
Surface area:
366.60 mm² vs 116.16 mm²
Difference: 250.44 mm² (216%)
ZV-E10 sensor is approx. 3.16x bigger than ZV-1 sensor.
Pixel pitch
3.89 µm
2.4 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 1.49 µm (62%)
Pixel pitch of ZV-E10 is approx. 62% higher than pixel pitch of ZV-1.
Pixel area
15.13 µm²
5.76 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 9.37 µm² (163%)
A pixel on Sony ZV-E10 sensor is approx. 163% bigger than a pixel on Sony ZV-1.
Pixel density
6.62 MP/cm²
17.31 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 10.69 µm (161%)
Sony ZV-1 has approx. 161% higher pixel density than Sony ZV-E10.
To learn about the accuracy of these numbers, click here.



Specs

Sony ZV-E10
Sony ZV-1
Crop factor
1.53
2.73
Total megapixels
25.00
21.00
Effective megapixels
24.20
20.10
Optical zoom
2.9x
Digital zoom
Yes
Yes
ISO sensitivity
Auto, 100-32000 (extends to 50-51200)
Auto, 125-12800
RAW
Manual focus
Normal focus range
5 cm
Macro focus range
5 cm
Focal length (35mm equiv.)
24 - 70 mm
Aperture priority
Yes
Yes
Max. aperture
f1.8 - f2.8
Max. aperture (35mm equiv.)
n/a
f4.9 - f7.6
Metering
Multi, Center-weighted, Spot
Multi, Center-weighted, Spot
Exposure compensation
±5 EV (in 1/3 EV, 1/2 EV steps)
±3 EV (in 1/3 EV steps)
Shutter priority
Yes
Yes
Min. shutter speed
30 sec
30 sec
Max. shutter speed
1/4000 sec
1/2000 sec
Built-in flash
External flash
Viewfinder
None
None
White balance presets
10
9
Screen size
3"
3"
Screen resolution
921,600 dots
921,600 dots
Video capture
Max. video resolution
3840x2160 (30p/​25p/​24p)
3840x2160 (30p/25p/24p)
Storage types
SD/SDHC/SDXC/MS Pro Duo
SD/ SDHC/SDXC/MS Pro Duo/ Pro-HG Duo
USB
USB 3.0 (5 GBit/sec)
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
NP-FW50 lithium-ion battery
NP-BX1 lithium-ion battery
Weight
343 g
294 g
Dimensions
115.2 x 64.2 x 44.8 mm
105.5 x 60 x 43.5 mm
Year
2021
2020




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Sony ZV-E10 diagonal

w = 23.50 mm
h = 15.60 mm
Diagonal =  23.50² + 15.60²   = 28.21 mm

Sony ZV-1 diagonal

w = 13.20 mm
h = 8.80 mm
Diagonal =  13.20² + 8.80²   = 15.86 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

ZV-E10 sensor area

Width = 23.50 mm
Height = 15.60 mm

Surface area = 23.50 × 15.60 = 366.60 mm²

ZV-1 sensor area

Width = 13.20 mm
Height = 8.80 mm

Surface area = 13.20 × 8.80 = 116.16 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

ZV-E10 pixel pitch

Sensor width = 23.50 mm
Sensor resolution width = 6045 pixels
Pixel pitch =   23.50  × 1000  = 3.89 µm
6045

ZV-1 pixel pitch

Sensor width = 13.20 mm
Sensor resolution width = 5492 pixels
Pixel pitch =   13.20  × 1000  = 2.4 µm
5492


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

ZV-E10 pixel area

Pixel pitch = 3.89 µm

Pixel area = 3.89² = 15.13 µm²

ZV-1 pixel area

Pixel pitch = 2.4 µm

Pixel area = 2.4² = 5.76 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

ZV-E10 pixel density

Sensor resolution width = 6045 pixels
Sensor width = 2.35 cm

Pixel density = (6045 / 2.35)² / 1000000 = 6.62 MP/cm²

ZV-1 pixel density

Sensor resolution width = 5492 pixels
Sensor width = 1.32 cm

Pixel density = (5492 / 1.32)² / 1000000 = 17.31 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

ZV-E10 sensor resolution

Sensor width = 23.50 mm
Sensor height = 15.60 mm
Effective megapixels = 24.20
r = 23.50/15.60 = 1.51
X =  24.20 × 1000000  = 4003
1.51
Resolution horizontal: X × r = 4003 × 1.51 = 6045
Resolution vertical: X = 4003

Sensor resolution = 6045 x 4003

ZV-1 sensor resolution

Sensor width = 13.20 mm
Sensor height = 8.80 mm
Effective megapixels = 20.10
r = 13.20/8.80 = 1.5
X =  20.10 × 1000000  = 3661
1.5
Resolution horizontal: X × r = 3661 × 1.5 = 5492
Resolution vertical: X = 3661

Sensor resolution = 5492 x 3661


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


ZV-E10 crop factor

Sensor diagonal in mm = 28.21 mm
Crop factor =   43.27  = 1.53
28.21

ZV-1 crop factor

Sensor diagonal in mm = 15.86 mm
Crop factor =   43.27  = 2.73
15.86

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

ZV-E10 equivalent aperture

Aperture is a lens characteristic, so it's calculated only for fixed lens cameras. If you want to know the equivalent aperture for Sony ZV-E10, take the aperture of the lens you're using and multiply it with crop factor.

Crop factor for Sony ZV-E10 is 1.53

ZV-1 equivalent aperture

Crop factor = 2.73
Aperture = f1.8 - f2.8

35-mm equivalent aperture = (f1.8 - f2.8) × 2.73 = f4.9 - f7.6

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.