Nikon Coolpix S9500 vs. Canon PowerShot SX260 HS

Comparison

change cameras »
Coolpix S9500 image
vs
PowerShot SX260 HS image
Nikon Coolpix S9500 Canon PowerShot SX260 HS
check price » check price »
Megapixels
18.10
12.10
Max. image resolution
4896 x 3672
4000 x 3000

Sensor

Sensor type
CMOS
CMOS
Sensor size
1/2.3" (~ 6.16 x 4.62 mm)
1/2.3" (~ 6.16 x 4.62 mm)
Sensor resolution
4906 x 3689
4011 x 3016
Diagonal
7.70 mm
7.70 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1 : 1
(ratio)
Nikon Coolpix S9500 Canon PowerShot SX260 HS
Surface area:
28.46 mm² vs 28.46 mm²
Difference: 0 mm² (0%)
S9500 and SX260 HS sensors are the same size.
Pixel pitch
1.26 µm
1.54 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 0.28 µm (22%)
Pixel pitch of SX260 HS is approx. 22% higher than pixel pitch of S9500.
Pixel area
1.59 µm²
2.37 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 0.78 µm² (49%)
A pixel on Canon SX260 HS sensor is approx. 49% bigger than a pixel on Nikon S9500.
Pixel density
63.43 MP/cm²
42.4 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 21.03 µm (50%)
Nikon S9500 has approx. 50% higher pixel density than Canon SX260 HS.
To learn about the accuracy of these numbers, click here.

Specs

Nikon S9500
Canon SX260 HS
Crop factor
5.62
5.62
Total megapixels
18.91
Effective megapixels
18.10
12.10
Optical zoom
22x
20x
Digital zoom
Yes
Yes
ISO sensitivity
ISO 125-3200
Auto, 100, 200, 400, 800, 1600, 3200
RAW
Manual focus
Normal focus range
50 cm
45 cm
Macro focus range
1 cm
5 cm
Focal length (35mm equiv.)
25 - 550 mm
25 - 500 mm
Aperture priority
No
Yes
Max. aperture
f3.4 - f6.3
f3.5 - f6.8
Max. aperture (35mm equiv.)
f19.1 - f35.4
f19.7 - f38.2
Metering
Matrix, Center-weighted, Spot
Centre weighted, Evaluative, Spot
Exposure compensation
±2 EV (in 1/3 EV steps)
±2 EV (in 1/3 EV steps)
Shutter priority
No
Yes
Min. shutter speed
4 sec
15 sec
Max. shutter speed
1/1500 sec
1/3200 sec
Built-in flash
External flash
Viewfinder
None
None
White balance presets
5
6
Screen size
3"
3"
Screen resolution
614,000 dots
461,000 dots
Video capture
Max. video resolution
1920x1080 (30p)
1920x1080 (24p)
Storage types
SD/SDHC/SDXC
SDHC, SDXC, Secure Digital
USB
USB 2.0 (480 Mbit/sec)
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
Rechargeable Li-ion Battery EN-EL12
Lithium-Ion NB-6L rechargeable battery
Weight
205 g
231 g
Dimensions
110.1 x 60.3 x 30.7 mm
105.5 x 61.0 x 32.7 mm
Year
2013
2012



Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Nikon S9500 diagonal

The diagonal of S9500 sensor is not 1/2.3 or 0.43" (11 mm) as you might expect, but approximately two thirds of that value - 7.7 mm. If you want to know why, see sensor sizes.

w = 6.16 mm
h = 4.62 mm
Diagonal =  6.16² + 4.62²   = 7.70 mm

Canon SX260 HS diagonal

The diagonal of SX260 HS sensor is not 1/2.3 or 0.43" (11 mm) as you might expect, but approximately two thirds of that value - 7.7 mm. If you want to know why, see sensor sizes.

w = 6.16 mm
h = 4.62 mm
Diagonal =  6.16² + 4.62²   = 7.70 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

S9500 sensor area

Width = 6.16 mm
Height = 4.62 mm

Surface area = 6.16 × 4.62 = 28.46 mm²

SX260 HS sensor area

Width = 6.16 mm
Height = 4.62 mm

Surface area = 6.16 × 4.62 = 28.46 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

S9500 pixel pitch

Sensor width = 6.16 mm
Sensor resolution width = 4906 pixels
Pixel pitch =   6.16  × 1000  = 1.26 µm
4906

SX260 HS pixel pitch

Sensor width = 6.16 mm
Sensor resolution width = 4011 pixels
Pixel pitch =   6.16  × 1000  = 1.54 µm
4011


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

S9500 pixel area

Pixel pitch = 1.26 µm

Pixel area = 1.26² = 1.59 µm²

SX260 HS pixel area

Pixel pitch = 1.54 µm

Pixel area = 1.54² = 2.37 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

S9500 pixel density

Sensor resolution width = 4906 pixels
Sensor width = 0.616 cm

Pixel density = (4906 / 0.616)² / 1000000 = 63.43 MP/cm²

SX260 HS pixel density

Sensor resolution width = 4011 pixels
Sensor width = 0.616 cm

Pixel density = (4011 / 0.616)² / 1000000 = 42.4 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

S9500 sensor resolution

Sensor width = 6.16 mm
Sensor height = 4.62 mm
Effective megapixels = 18.10
r = 6.16/4.62 = 1.33
X =  18.10 × 1000000  = 3689
1.33
Resolution horizontal: X × r = 3689 × 1.33 = 4906
Resolution vertical: X = 3689

Sensor resolution = 4906 x 3689

SX260 HS sensor resolution

Sensor width = 6.16 mm
Sensor height = 4.62 mm
Effective megapixels = 12.10
r = 6.16/4.62 = 1.33
X =  12.10 × 1000000  = 3016
1.33
Resolution horizontal: X × r = 3016 × 1.33 = 4011
Resolution vertical: X = 3016

Sensor resolution = 4011 x 3016


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


S9500 crop factor

Sensor diagonal in mm = 7.70 mm
Crop factor =   43.27  = 5.62
7.70

SX260 HS crop factor

Sensor diagonal in mm = 7.70 mm
Crop factor =   43.27  = 5.62
7.70

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

S9500 equivalent aperture

Crop factor = 5.62
Aperture = f3.4 - f6.3

35-mm equivalent aperture = (f3.4 - f6.3) × 5.62 = f19.1 - f35.4

SX260 HS equivalent aperture

Crop factor = 5.62
Aperture = f3.5 - f6.8

35-mm equivalent aperture = (f3.5 - f6.8) × 5.62 = f19.7 - f38.2

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.