BenQ DC 2300 vs. Canon EOS-1D Mark IV
Comparison
| change cameras » | |||||
|
vs |
|
|||
| BenQ DC 2300 | Canon EOS-1D Mark IV | ||||
| check price » | check price » | ||||
Megapixels
1.92
16.10
Max. image resolution
2048 x 1536
4896 x 3264
Sensor
Sensor type
CCD
CMOS
Sensor size
1/3.2" (~ 4.5 x 3.37 mm)
27.9 x 18.6 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera.
Sensors can vary greatly in size. As a general rule, the bigger the
sensor, the better the image quality.
Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.
Learn more about sensor sizes »
Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.
Learn more about sensor sizes »
Actual sensor size
Note: Actual size is set to screen → change »
|
|
vs |
|
| 1 | : | 34.21 |
| (ratio) | ||
| BenQ DC 2300 | Canon EOS-1D Mark IV | |
Surface area:
| 15.17 mm² | vs | 518.94 mm² |
Difference: 503.77 mm² (3321%)
-1D Mark IV sensor is approx. 34.21x bigger than DC 2300 sensor.
Note: You are comparing sensors of very different generations.
There is a gap of 6 years between BenQ DC 2300 (2003) and Canon -1D Mark IV (2009).
Six years is a lot of time in terms
of technology, meaning newer sensors are overall much more
efficient than the older ones.
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.
The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Pixel or photosite area affects how much light per pixel can be gathered.
The larger it is the more light can be collected by a single pixel.
Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 24.36 µm² (308%)
A pixel on Canon -1D Mark IV sensor is approx. 308% bigger than a pixel on BenQ DC 2300.
Pixel density tells you how many million pixels fit or would fit in one
square cm of the sensor.
Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Higher pixel density means smaller pixels and lower pixel density means larger pixels.
To learn about the accuracy of these numbers,
click here.
Specs
BenQ DC 2300
Canon -1D Mark IV
Total megapixels
17.00
Effective megapixels
16.10
Optical zoom
No
Digital zoom
Yes
No
ISO sensitivity
100, 200
100, 200, 400, 800, 1600, 3200, 6400, 12800 (50, 25600, 51200 and 102400 with boost)
RAW
Manual focus
Normal focus range
80 cm
Macro focus range
18 cm
Focal length (35mm equiv.)
43 mm
Aperture priority
No
Yes
Max. aperture
f3.5
Metering
Centre weighted
63-zone Evaluative, Centre weighted, Spot
Exposure compensation
±2 EV (in 1/2 EV steps)
±3 EV (in 1/3 EV, 1/2 EV steps)
Shutter priority
No
Yes
Min. shutter speed
1/4 sec
30 sec
Max. shutter speed
1/1000 sec
1/8000 sec
Built-in flash
External flash
Viewfinder
Optical
Optical (pentaprism)
White balance presets
5
8
Screen size
1.6"
3"
Screen resolution
920,000 dots
Video capture
Max. video resolution
Storage types
MultiMedia, Secure Digital
CompactFlash type I, CompactFlash type II, SDHC, Secure Digital
USB
USB 1.1
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
2x AA
Lithium-Ion LP-E4 rechargeable battery
Weight
145 g
1230 g
Dimensions
94 x 66 x 40 mm
156 x 157 x 80 mm
Year
2003
2009
Choose cameras to compare
Popular comparisons:
- BenQ DC 2300 vs. BenQ DC C1420
- BenQ DC 2300 vs. Nikon Coolpix L310
- BenQ DC 2300 vs. AgfaPhoto DC-1033m
- BenQ DC 2300 vs. Canon EOS-1D Mark IV
- BenQ DC 2300 vs. Canon Digital IXUS 110 IS
- BenQ DC 2300 vs. Canon Digital IXUS 400
- BenQ DC 2300 vs. Canon PowerShot SX150 IS
- BenQ DC 2300 vs. BenQ DC 4500
- BenQ DC 2300 vs. Pentax 645D
- BenQ DC 2300 vs. Canon EOS R5 Mark II
- BenQ DC 2300 vs. Contax SL300R T
Diagonal
Diagonal is calculated by the use of Pythagorean theorem:
where w = sensor width and h = sensor height
| Diagonal = √ | w² + h² |
BenQ DC 2300 diagonal
The diagonal of DC 2300 sensor is not 1/3.2 or 0.31" (7.9 mm) as you might expect, but approximately two thirds of
that value - 5.62 mm. If you want to know why, see
sensor sizes.
w = 4.50 mm
h = 3.37 mm
w = 4.50 mm
h = 3.37 mm
| Diagonal = √ | 4.50² + 3.37² | = 5.62 mm |
Canon -1D Mark IV diagonal
w = 27.90 mm
h = 18.60 mm
h = 18.60 mm
| Diagonal = √ | 27.90² + 18.60² | = 33.53 mm |
Surface area
Surface area is calculated by multiplying the width and the height of a sensor.
DC 2300 sensor area
Width = 4.50 mm
Height = 3.37 mm
Surface area = 4.50 × 3.37 = 15.17 mm²
Height = 3.37 mm
Surface area = 4.50 × 3.37 = 15.17 mm²
-1D Mark IV sensor area
Width = 27.90 mm
Height = 18.60 mm
Surface area = 27.90 × 18.60 = 518.94 mm²
Height = 18.60 mm
Surface area = 27.90 × 18.60 = 518.94 mm²
Pixel pitch
Pixel pitch is the distance from the center of one pixel to the center of the
next measured in micrometers (µm). It can be calculated with the following formula:
| Pixel pitch = | sensor width in mm | × 1000 |
| sensor resolution width in pixels |
DC 2300 pixel pitch
Sensor width = 4.50 mm
Sensor resolution width = 1604 pixels
Sensor resolution width = 1604 pixels
| Pixel pitch = | 4.50 | × 1000 | = 2.81 µm |
| 1604 |
-1D Mark IV pixel pitch
Sensor width = 27.90 mm
Sensor resolution width = 4914 pixels
Sensor resolution width = 4914 pixels
| Pixel pitch = | 27.90 | × 1000 | = 5.68 µm |
| 4914 |
Pixel area
The area of one pixel can be calculated by simply squaring the pixel pitch:
You could also divide sensor surface area with effective megapixels:
Pixel area = pixel pitch²
You could also divide sensor surface area with effective megapixels:
| Pixel area = | sensor surface area in mm² |
| effective megapixels |
DC 2300 pixel area
Pixel pitch = 2.81 µm
Pixel area = 2.81² = 7.9 µm²
Pixel area = 2.81² = 7.9 µm²
-1D Mark IV pixel area
Pixel pitch = 5.68 µm
Pixel area = 5.68² = 32.26 µm²
Pixel area = 5.68² = 32.26 µm²
Pixel density
Pixel density can be calculated with the following formula:
One could also use this formula:
| Pixel density = ( | sensor resolution width in pixels | )² / 1000000 |
| sensor width in cm |
One could also use this formula:
| Pixel density = | effective megapixels × 1000000 | / 10000 |
| sensor surface area in mm² |
DC 2300 pixel density
Sensor resolution width = 1604 pixels
Sensor width = 0.45 cm
Pixel density = (1604 / 0.45)² / 1000000 = 12.71 MP/cm²
Sensor width = 0.45 cm
Pixel density = (1604 / 0.45)² / 1000000 = 12.71 MP/cm²
-1D Mark IV pixel density
Sensor resolution width = 4914 pixels
Sensor width = 2.79 cm
Pixel density = (4914 / 2.79)² / 1000000 = 3.1 MP/cm²
Sensor width = 2.79 cm
Pixel density = (4914 / 2.79)² / 1000000 = 3.1 MP/cm²
Sensor resolution
Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher
than maximum (not interpolated) image resolution which is usually stated on camera specifications.
Sensor resolution is used in pixel pitch, pixel area, and pixel density formula.
For sake of simplicity, we're going to calculate it in 3 stages.
1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.
2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
3. To get sensor resolution we then multiply X with the corresponding ratio:
Resolution horizontal: X × r
Resolution vertical: X
1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.
2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
| (X × r) × X = effective megapixels × 1000000 → |
|
Resolution horizontal: X × r
Resolution vertical: X
DC 2300 sensor resolution
Sensor width = 4.50 mm
Sensor height = 3.37 mm
Effective megapixels = 1.92
Resolution horizontal: X × r = 1197 × 1.34 = 1604
Resolution vertical: X = 1197
Sensor resolution = 1604 x 1197
Sensor height = 3.37 mm
Effective megapixels = 1.92
| r = 4.50/3.37 = 1.34 |
|
Resolution vertical: X = 1197
Sensor resolution = 1604 x 1197
-1D Mark IV sensor resolution
Sensor width = 27.90 mm
Sensor height = 18.60 mm
Effective megapixels = 16.10
Resolution horizontal: X × r = 3276 × 1.5 = 4914
Resolution vertical: X = 3276
Sensor resolution = 4914 x 3276
Sensor height = 18.60 mm
Effective megapixels = 16.10
| r = 27.90/18.60 = 1.5 |
|
Resolution vertical: X = 3276
Sensor resolution = 4914 x 3276
Crop factor
Crop factor or focal length multiplier is calculated by dividing the diagonal
of 35 mm film (43.27 mm) with the diagonal of the sensor.
| Crop factor = | 43.27 mm |
| sensor diagonal in mm |
DC 2300 crop factor
Sensor diagonal in mm = 5.62 mm
| Crop factor = | 43.27 | = 7.7 |
| 5.62 |
-1D Mark IV crop factor
Sensor diagonal in mm = 33.53 mm
| Crop factor = | 43.27 | = 1.29 |
| 33.53 |
35 mm equivalent aperture
Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture
with crop factor (a.k.a. focal length multiplier).
DC 2300 equivalent aperture
Crop factor = 7.7
Aperture = f3.5
35-mm equivalent aperture = (f3.5) × 7.7 = f27
Aperture = f3.5
35-mm equivalent aperture = (f3.5) × 7.7 = f27
-1D Mark IV equivalent aperture
Aperture is a lens characteristic, so it's calculated only for
fixed lens cameras. If you want to know the equivalent aperture for
Canon -1D Mark IV, take the aperture of the lens
you're using and multiply it with crop factor.
Crop factor for Canon -1D Mark IV is 1.29
Crop factor for Canon -1D Mark IV is 1.29
Enter your screen size (diagonal)
My screen size is
inches
Actual size is currently adjusted to screen.
If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.
If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.