Canon IXY 220F vs. Canon IXY 420F

Comparison

change cameras »
IXY 220F image
vs
IXY 420F image
Canon IXY 220F Canon IXY 420F
check price » check price »
Megapixels
16.10
16.10
Max. image resolution
4608 x 3456
4608 x 3456

Sensor

Sensor type
CMOS
CMOS
Sensor size
1/2.3" (~ 6.16 x 4.62 mm)
1/2.3" (~ 6.16 x 4.62 mm)
Sensor resolution
4627 x 3479
4627 x 3479
Diagonal
7.70 mm
7.70 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1 : 1
(ratio)
Canon IXY 220F Canon IXY 420F
Surface area:
28.46 mm² vs 28.46 mm²
Difference: 0 mm² (0%)
IXY 220F and IXY 420F sensors are the same size.
Pixel pitch
1.33 µm
1.33 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 0 µm (0%)
IXY 220F and IXY 420F have the same pixel pitch.
Pixel area
1.77 µm²
1.77 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 0 µm² (0%)
Canon IXY 220F and Canon IXY 420F have the same pixel area.
Pixel density
56.42 MP/cm²
56.42 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 0 µm (0%)
Canon IXY 220F and Canon IXY 420F have the same pixel density.
To learn about the accuracy of these numbers, click here.



Specs

Canon IXY 220F
Canon IXY 420F
Crop factor
5.62
5.62
Total megapixels
Effective megapixels
16.10
16.10
Optical zoom
5x
5x
Digital zoom
Yes
Yes
ISO sensitivity
Auto, 100, 200, 400, 800, 1600, 3200
Auto, 100, 200, 400, 800, 1600, 3200
RAW
Manual focus
Normal focus range
Macro focus range
3 cm
3 cm
Focal length (35mm equiv.)
24 - 120 mm
24 - 120 mm
Aperture priority
No
No
Max. aperture
f2.7 - f5.9
f2.7 - f5.9
Max. aperture (35mm equiv.)
f15.2 - f33.2
f15.2 - f33.2
Metering
Multi, Center-weighted, Spot
Multi, Center-weighted, Spot
Exposure compensation
±2 EV (in 1/3 EV steps)
±2 EV (in 1/3 EV steps)
Shutter priority
No
No
Min. shutter speed
15 sec
15 sec
Max. shutter speed
1/2000 sec
1/2000 sec
Built-in flash
External flash
Viewfinder
None
None
White balance presets
6
6
Screen size
3"
3.2"
Screen resolution
461,000 dots
461,000 dots
Video capture
Max. video resolution
Storage types
SD/SDHC/SDXC
SD/SDHC/SDXC
USB
USB 2.0 (480 Mbit/sec)
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
Lithium-Ion NB-11L rechargeable battery
Lithium-Ion NB-11L rechargeable battery
Weight
135 g
145 g
Dimensions
93 x 57 x 20 mm
94 x 57 x 21 mm
Year
2012
2012




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Canon IXY 220F diagonal

The diagonal of IXY 220F sensor is not 1/2.3 or 0.43" (11 mm) as you might expect, but approximately two thirds of that value - 7.7 mm. If you want to know why, see sensor sizes.

w = 6.16 mm
h = 4.62 mm
Diagonal =  6.16² + 4.62²   = 7.70 mm

Canon IXY 420F diagonal

The diagonal of IXY 420F sensor is not 1/2.3 or 0.43" (11 mm) as you might expect, but approximately two thirds of that value - 7.7 mm. If you want to know why, see sensor sizes.

w = 6.16 mm
h = 4.62 mm
Diagonal =  6.16² + 4.62²   = 7.70 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

IXY 220F sensor area

Width = 6.16 mm
Height = 4.62 mm

Surface area = 6.16 × 4.62 = 28.46 mm²

IXY 420F sensor area

Width = 6.16 mm
Height = 4.62 mm

Surface area = 6.16 × 4.62 = 28.46 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

IXY 220F pixel pitch

Sensor width = 6.16 mm
Sensor resolution width = 4627 pixels
Pixel pitch =   6.16  × 1000  = 1.33 µm
4627

IXY 420F pixel pitch

Sensor width = 6.16 mm
Sensor resolution width = 4627 pixels
Pixel pitch =   6.16  × 1000  = 1.33 µm
4627


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

IXY 220F pixel area

Pixel pitch = 1.33 µm

Pixel area = 1.33² = 1.77 µm²

IXY 420F pixel area

Pixel pitch = 1.33 µm

Pixel area = 1.33² = 1.77 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

IXY 220F pixel density

Sensor resolution width = 4627 pixels
Sensor width = 0.616 cm

Pixel density = (4627 / 0.616)² / 1000000 = 56.42 MP/cm²

IXY 420F pixel density

Sensor resolution width = 4627 pixels
Sensor width = 0.616 cm

Pixel density = (4627 / 0.616)² / 1000000 = 56.42 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

IXY 220F sensor resolution

Sensor width = 6.16 mm
Sensor height = 4.62 mm
Effective megapixels = 16.10
r = 6.16/4.62 = 1.33
X =  16.10 × 1000000  = 3479
1.33
Resolution horizontal: X × r = 3479 × 1.33 = 4627
Resolution vertical: X = 3479

Sensor resolution = 4627 x 3479

IXY 420F sensor resolution

Sensor width = 6.16 mm
Sensor height = 4.62 mm
Effective megapixels = 16.10
r = 6.16/4.62 = 1.33
X =  16.10 × 1000000  = 3479
1.33
Resolution horizontal: X × r = 3479 × 1.33 = 4627
Resolution vertical: X = 3479

Sensor resolution = 4627 x 3479


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


IXY 220F crop factor

Sensor diagonal in mm = 7.70 mm
Crop factor =   43.27  = 5.62
7.70

IXY 420F crop factor

Sensor diagonal in mm = 7.70 mm
Crop factor =   43.27  = 5.62
7.70

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

IXY 220F equivalent aperture

Crop factor = 5.62
Aperture = f2.7 - f5.9

35-mm equivalent aperture = (f2.7 - f5.9) × 5.62 = f15.2 - f33.2

IXY 420F equivalent aperture

Crop factor = 5.62
Aperture = f2.7 - f5.9

35-mm equivalent aperture = (f2.7 - f5.9) × 5.62 = f15.2 - f33.2

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.