Canon IXY DIGITAL 110 IS vs. Canon PowerShot SX740 HS

Comparison

change cameras »
IXY DIGITAL 110 IS image
vs
PowerShot SX740 HS image
Canon IXY DIGITAL 110 IS Canon PowerShot SX740 HS
check price » check price »
Megapixels
10.00
20.30
Max. image resolution
3648 x 2736
5184 x 3888

Sensor

Sensor type
CCD
CMOS
Sensor size
1/2.3" (~ 6.16 x 4.62 mm)
1/2.3" (~ 6.16 x 4.62 mm)
Sensor resolution
3647 x 2742
5196 x 3907
Diagonal
7.70 mm
7.70 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1 : 1
(ratio)
Canon IXY DIGITAL 110 IS Canon PowerShot SX740 HS
Surface area:
28.46 mm² vs 28.46 mm²
Difference: 0 mm² (0%)
IXY DIGITAL 110 IS and SX740 HS sensors are the same size.
Note: You are comparing sensors of very different generations. There is a gap of 9 years between Canon IXY DIGITAL 110 IS (2009) and Canon SX740 HS (2018). Nine years is a lot of time in terms of technology, meaning newer sensors are overall much more efficient than the older ones.
Pixel pitch
1.69 µm
1.19 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 0.5 µm (42%)
Pixel pitch of IXY DIGITAL 110 IS is approx. 42% higher than pixel pitch of SX740 HS.
Pixel area
2.86 µm²
1.42 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 1.44 µm² (101%)
A pixel on Canon IXY DIGITAL 110 IS sensor is approx. 101% bigger than a pixel on Canon SX740 HS.
Pixel density
35.05 MP/cm²
71.15 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 36.1 µm (103%)
Canon SX740 HS has approx. 103% higher pixel density than Canon IXY DIGITAL 110 IS.
To learn about the accuracy of these numbers, click here.



Specs

Canon IXY DIGITAL 110 IS
Canon SX740 HS
Crop factor
5.62
5.62
Total megapixels
21.10
Effective megapixels
10.00
20.30
Optical zoom
3x
40x
Digital zoom
Yes
Yes
ISO sensitivity
Auto, 80, 100, 200, 400, 800, 1600
Auto, 100-3200
RAW
Manual focus
Normal focus range
50 cm
5 cm
Macro focus range
3 cm
1 cm
Focal length (35mm equiv.)
35 - 105 mm
24 - 960 mm
Aperture priority
No
Yes
Max. aperture
f2.8 - f4.9
f3.3 - f6.9
Max. aperture (35mm equiv.)
f15.7 - f27.5
f18.5 - f38.8
Metering
Centre weighted, Evaluative, Spot
Multi, Center-weighted, Spot
Exposure compensation
±2 EV (in 1/3 EV steps)
±3 EV (in 1/3 EV steps)
Shutter priority
No
Yes
Min. shutter speed
15 sec
15 sec
Max. shutter speed
1/1500 sec
1/3200 sec
Built-in flash
External flash
Viewfinder
None
None
White balance presets
6
5
Screen size
2,5"
3"
Screen resolution
230,000 dots
921,600 dots
Video capture
Max. video resolution
3840x2160 (30p/25p)
Storage types
SD/SDHC/MMC/MMCplus/HD MMCplus
SD/SDHC/SDXC
USB
USB 2.0 (480 Mbit/sec)
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
Lithium-Ion NB-6L battery
NB-13L lithium-ion battery
Weight
160 g
299 g
Dimensions
86 x 55 x 22 mm
110.1 x 63.8 x 39.9 mm
Year
2009
2018




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Canon IXY DIGITAL 110 IS diagonal

The diagonal of IXY DIGITAL 110 IS sensor is not 1/2.3 or 0.43" (11 mm) as you might expect, but approximately two thirds of that value - 7.7 mm. If you want to know why, see sensor sizes.

w = 6.16 mm
h = 4.62 mm
Diagonal =  6.16² + 4.62²   = 7.70 mm

Canon SX740 HS diagonal

The diagonal of SX740 HS sensor is not 1/2.3 or 0.43" (11 mm) as you might expect, but approximately two thirds of that value - 7.7 mm. If you want to know why, see sensor sizes.

w = 6.16 mm
h = 4.62 mm
Diagonal =  6.16² + 4.62²   = 7.70 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

IXY DIGITAL 110 IS sensor area

Width = 6.16 mm
Height = 4.62 mm

Surface area = 6.16 × 4.62 = 28.46 mm²

SX740 HS sensor area

Width = 6.16 mm
Height = 4.62 mm

Surface area = 6.16 × 4.62 = 28.46 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

IXY DIGITAL 110 IS pixel pitch

Sensor width = 6.16 mm
Sensor resolution width = 3647 pixels
Pixel pitch =   6.16  × 1000  = 1.69 µm
3647

SX740 HS pixel pitch

Sensor width = 6.16 mm
Sensor resolution width = 5196 pixels
Pixel pitch =   6.16  × 1000  = 1.19 µm
5196


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

IXY DIGITAL 110 IS pixel area

Pixel pitch = 1.69 µm

Pixel area = 1.69² = 2.86 µm²

SX740 HS pixel area

Pixel pitch = 1.19 µm

Pixel area = 1.19² = 1.42 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

IXY DIGITAL 110 IS pixel density

Sensor resolution width = 3647 pixels
Sensor width = 0.616 cm

Pixel density = (3647 / 0.616)² / 1000000 = 35.05 MP/cm²

SX740 HS pixel density

Sensor resolution width = 5196 pixels
Sensor width = 0.616 cm

Pixel density = (5196 / 0.616)² / 1000000 = 71.15 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

IXY DIGITAL 110 IS sensor resolution

Sensor width = 6.16 mm
Sensor height = 4.62 mm
Effective megapixels = 10.00
r = 6.16/4.62 = 1.33
X =  10.00 × 1000000  = 2742
1.33
Resolution horizontal: X × r = 2742 × 1.33 = 3647
Resolution vertical: X = 2742

Sensor resolution = 3647 x 2742

SX740 HS sensor resolution

Sensor width = 6.16 mm
Sensor height = 4.62 mm
Effective megapixels = 20.30
r = 6.16/4.62 = 1.33
X =  20.30 × 1000000  = 3907
1.33
Resolution horizontal: X × r = 3907 × 1.33 = 5196
Resolution vertical: X = 3907

Sensor resolution = 5196 x 3907


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


IXY DIGITAL 110 IS crop factor

Sensor diagonal in mm = 7.70 mm
Crop factor =   43.27  = 5.62
7.70

SX740 HS crop factor

Sensor diagonal in mm = 7.70 mm
Crop factor =   43.27  = 5.62
7.70

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

IXY DIGITAL 110 IS equivalent aperture

Crop factor = 5.62
Aperture = f2.8 - f4.9

35-mm equivalent aperture = (f2.8 - f4.9) × 5.62 = f15.7 - f27.5

SX740 HS equivalent aperture

Crop factor = 5.62
Aperture = f3.3 - f6.9

35-mm equivalent aperture = (f3.3 - f6.9) × 5.62 = f18.5 - f38.8

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.