Canon PowerShot G1 X Mark III vs. Sony Cyber-shot DSC-RX100 V

Comparison

change cameras »
PowerShot G1 X Mark III image
vs
Cyber-shot DSC-RX100 V image
Canon PowerShot G1 X Mark III Sony Cyber-shot DSC-RX100 V
check price » check price »
Megapixels
24.20
20.10
Max. image resolution
6000 x 4000
5472 x 3648

Sensor

Sensor type
CMOS
CMOS
Sensor size
22.3 x 14.9 mm
13.2 x 8.8 mm
Sensor resolution
6026 x 4017
5492 x 3661
Diagonal
26.82 mm
15.86 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
2.86 : 1
(ratio)
Canon PowerShot G1 X Mark III Sony Cyber-shot DSC-RX100 V
Surface area:
332.27 mm² vs 116.16 mm²
Difference: 216.11 mm² (186%)
G1 X Mark III sensor is approx. 2.86x bigger than RX100 V sensor.
Pixel pitch
3.7 µm
2.4 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 1.3 µm (54%)
Pixel pitch of G1 X Mark III is approx. 54% higher than pixel pitch of RX100 V.
Pixel area
13.69 µm²
5.76 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 7.93 µm² (138%)
A pixel on Canon G1 X Mark III sensor is approx. 138% bigger than a pixel on Sony RX100 V.
Pixel density
7.3 MP/cm²
17.31 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 10.01 µm (137%)
Sony RX100 V has approx. 137% higher pixel density than Canon G1 X Mark III.
To learn about the accuracy of these numbers, click here.

Specs

Canon G1 X Mark III
Sony RX100 V
Crop factor
1.61
2.73
Total megapixels
25.80
21.00
Effective megapixels
24.20
20.10
Optical zoom
3x
2.9x
Digital zoom
Yes
Yes
ISO sensitivity
Auto, 100-25600
Auto, 125-12800
RAW
Manual focus
Normal focus range
10 cm
5 cm
Macro focus range
10 cm
5 cm
Focal length (35mm equiv.)
24 - 72 mm
24 - 70 mm
Aperture priority
Yes
Yes
Max. aperture
f2.8 - f5.6
f1.8 - f2.8
Max. aperture (35mm equiv.)
f4.5 - f9
f4.9 - f7.6
Metering
Multi, Center-weighted, Spot
Multi, Center-weighted, Spot
Exposure compensation
±3 EV (in 1/3 EV steps)
±3 EV (in 1/3 EV steps)
Shutter priority
Yes
Yes
Min. shutter speed
30 sec
30 sec
Max. shutter speed
1/2000 sec
1/2000 sec
Built-in flash
External flash
Viewfinder
Electronic
Electronic
White balance presets
7
9
Screen size
3"
3"
Screen resolution
1,040,000 dots
1,228,800 dots
Video capture
Max. video resolution
1920x1080 (60p/50p/30p/25p/24p)
3840x2160 (30p/25p/24p)
Storage types
SD/SDHC/SDXC
SD/ SDHC/SDXC/MS Duo/MS PRO Duo
USB
USB 2.0 (480 Mbit/sec)
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
NB-13L lithium-ion battery
NP-BX1 lithium-ion battery
Weight
399 g
299 g
Dimensions
115 x 77.9 x 51.4 mm
101.6 x 58.1 x 41 mm
Year
2017
2016



Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Canon G1 X Mark III diagonal

w = 22.30 mm
h = 14.90 mm
Diagonal =  22.30² + 14.90²   = 26.82 mm

Sony RX100 V diagonal

w = 13.20 mm
h = 8.80 mm
Diagonal =  13.20² + 8.80²   = 15.86 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

G1 X Mark III sensor area

Width = 22.30 mm
Height = 14.90 mm

Surface area = 22.30 × 14.90 = 332.27 mm²

RX100 V sensor area

Width = 13.20 mm
Height = 8.80 mm

Surface area = 13.20 × 8.80 = 116.16 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

G1 X Mark III pixel pitch

Sensor width = 22.30 mm
Sensor resolution width = 6026 pixels
Pixel pitch =   22.30  × 1000  = 3.7 µm
6026

RX100 V pixel pitch

Sensor width = 13.20 mm
Sensor resolution width = 5492 pixels
Pixel pitch =   13.20  × 1000  = 2.4 µm
5492


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

G1 X Mark III pixel area

Pixel pitch = 3.7 µm

Pixel area = 3.7² = 13.69 µm²

RX100 V pixel area

Pixel pitch = 2.4 µm

Pixel area = 2.4² = 5.76 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

G1 X Mark III pixel density

Sensor resolution width = 6026 pixels
Sensor width = 2.23 cm

Pixel density = (6026 / 2.23)² / 1000000 = 7.3 MP/cm²

RX100 V pixel density

Sensor resolution width = 5492 pixels
Sensor width = 1.32 cm

Pixel density = (5492 / 1.32)² / 1000000 = 17.31 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

G1 X Mark III sensor resolution

Sensor width = 22.30 mm
Sensor height = 14.90 mm
Effective megapixels = 24.20
r = 22.30/14.90 = 1.5
X =  24.20 × 1000000  = 4017
1.5
Resolution horizontal: X × r = 4017 × 1.5 = 6026
Resolution vertical: X = 4017

Sensor resolution = 6026 x 4017

RX100 V sensor resolution

Sensor width = 13.20 mm
Sensor height = 8.80 mm
Effective megapixels = 20.10
r = 13.20/8.80 = 1.5
X =  20.10 × 1000000  = 3661
1.5
Resolution horizontal: X × r = 3661 × 1.5 = 5492
Resolution vertical: X = 3661

Sensor resolution = 5492 x 3661


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


G1 X Mark III crop factor

Sensor diagonal in mm = 26.82 mm
Crop factor =   43.27  = 1.61
26.82

RX100 V crop factor

Sensor diagonal in mm = 15.86 mm
Crop factor =   43.27  = 2.73
15.86

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

G1 X Mark III equivalent aperture

Crop factor = 1.61
Aperture = f2.8 - f5.6

35-mm equivalent aperture = (f2.8 - f5.6) × 1.61 = f4.5 - f9

RX100 V equivalent aperture

Crop factor = 2.73
Aperture = f1.8 - f2.8

35-mm equivalent aperture = (f1.8 - f2.8) × 2.73 = f4.9 - f7.6

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.