Canon PowerShot SD1000 vs. Canon PowerShot ELPH 300 HS

Comparison

change cameras »
PowerShot SD1000 image
vs
PowerShot ELPH 300 HS image
Canon PowerShot SD1000 Canon PowerShot ELPH 300 HS
check price » check price »
Megapixels
7.10
12.10
Max. image resolution
3072 x 2304
4000 x 3000

Sensor

Sensor type
CCD
CMOS
Sensor size
1/2.5" (~ 5.75 x 4.32 mm)
1/2.3" (~ 6.16 x 4.62 mm)
Sensor resolution
3072 x 2310
4011 x 3016
Diagonal
7.19 mm
7.70 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1 : 1.15
(ratio)
Canon PowerShot SD1000 Canon PowerShot ELPH 300 HS
Surface area:
24.84 mm² vs 28.46 mm²
Difference: 3.62 mm² (15%)
ELPH 300 HS sensor is approx. 1.15x bigger than SD1000 sensor.
Note: You are comparing cameras of different generations. There is a 4 year gap between Canon SD1000 (2007) and Canon ELPH 300 HS (2011). All things being equal, newer sensor generations generally outperform the older.
Pixel pitch
1.87 µm
1.54 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 0.33 µm (21%)
Pixel pitch of SD1000 is approx. 21% higher than pixel pitch of ELPH 300 HS.
Pixel area
3.5 µm²
2.37 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 1.13 µm² (48%)
A pixel on Canon SD1000 sensor is approx. 48% bigger than a pixel on Canon ELPH 300 HS.
Pixel density
28.54 MP/cm²
42.4 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 13.86 µm (49%)
Canon ELPH 300 HS has approx. 49% higher pixel density than Canon SD1000.
To learn about the accuracy of these numbers, click here.



Specs

Canon SD1000
Canon ELPH 300 HS
Crop factor
6.02
5.62
Total megapixels
7.40
Effective megapixels
7.10
12.10
Optical zoom
3x
5x
Digital zoom
Yes
Yes
ISO sensitivity
Auto, 80 ,100, 200, 400, 800, 1600
Auto, 100 - 3200
RAW
Manual focus
Normal focus range
45 cm
40 cm
Macro focus range
5 cm
3 cm
Focal length (35mm equiv.)
35 - 105 mm
24 - 120 mm
Aperture priority
No
No
Max. aperture
f2.8 - f4.9
f2.7 - f5.9
Max. aperture (35mm equiv.)
f16.9 - f29.5
f15.2 - f33.2
Metering
Multi, Center-weighted, Spot
Centre weighted, Evaluative, Spot
Exposure compensation
±2 EV (in 1/3 EV steps)
±2 EV (in 1/3 EV steps)
Shutter priority
No
No
Min. shutter speed
15 sec
15 sec
Max. shutter speed
1/1500 sec
1/2000 sec
Built-in flash
External flash
Viewfinder
Optical (tunnel)
None
White balance presets
5
6
Screen size
2.5"
2.7"
Screen resolution
230,000 dots
230,000 dots
Video capture
Max. video resolution
Storage types
SD/SDHC card
SDHC, SDXC, Secure Digital
USB
USB 2.0 (480 Mbit/sec)
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
Lithium-Ion NB-4L battery
Lithium-Ion NB-4L rechargeable battery
Weight
175 g
141 g
Dimensions
86 x 54 x 19 mm
92.2 x 55.9 x 19.5 mm
Year
2007
2011




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Canon SD1000 diagonal

The diagonal of SD1000 sensor is not 1/2.5 or 0.4" (10.2 mm) as you might expect, but approximately two thirds of that value - 7.19 mm. If you want to know why, see sensor sizes.

w = 5.75 mm
h = 4.32 mm
Diagonal =  5.75² + 4.32²   = 7.19 mm

Canon ELPH 300 HS diagonal

The diagonal of ELPH 300 HS sensor is not 1/2.3 or 0.43" (11 mm) as you might expect, but approximately two thirds of that value - 7.7 mm. If you want to know why, see sensor sizes.

w = 6.16 mm
h = 4.62 mm
Diagonal =  6.16² + 4.62²   = 7.70 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

SD1000 sensor area

Width = 5.75 mm
Height = 4.32 mm

Surface area = 5.75 × 4.32 = 24.84 mm²

ELPH 300 HS sensor area

Width = 6.16 mm
Height = 4.62 mm

Surface area = 6.16 × 4.62 = 28.46 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

SD1000 pixel pitch

Sensor width = 5.75 mm
Sensor resolution width = 3072 pixels
Pixel pitch =   5.75  × 1000  = 1.87 µm
3072

ELPH 300 HS pixel pitch

Sensor width = 6.16 mm
Sensor resolution width = 4011 pixels
Pixel pitch =   6.16  × 1000  = 1.54 µm
4011


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

SD1000 pixel area

Pixel pitch = 1.87 µm

Pixel area = 1.87² = 3.5 µm²

ELPH 300 HS pixel area

Pixel pitch = 1.54 µm

Pixel area = 1.54² = 2.37 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

SD1000 pixel density

Sensor resolution width = 3072 pixels
Sensor width = 0.575 cm

Pixel density = (3072 / 0.575)² / 1000000 = 28.54 MP/cm²

ELPH 300 HS pixel density

Sensor resolution width = 4011 pixels
Sensor width = 0.616 cm

Pixel density = (4011 / 0.616)² / 1000000 = 42.4 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

SD1000 sensor resolution

Sensor width = 5.75 mm
Sensor height = 4.32 mm
Effective megapixels = 7.10
r = 5.75/4.32 = 1.33
X =  7.10 × 1000000  = 2310
1.33
Resolution horizontal: X × r = 2310 × 1.33 = 3072
Resolution vertical: X = 2310

Sensor resolution = 3072 x 2310

ELPH 300 HS sensor resolution

Sensor width = 6.16 mm
Sensor height = 4.62 mm
Effective megapixels = 12.10
r = 6.16/4.62 = 1.33
X =  12.10 × 1000000  = 3016
1.33
Resolution horizontal: X × r = 3016 × 1.33 = 4011
Resolution vertical: X = 3016

Sensor resolution = 4011 x 3016


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


SD1000 crop factor

Sensor diagonal in mm = 7.19 mm
Crop factor =   43.27  = 6.02
7.19

ELPH 300 HS crop factor

Sensor diagonal in mm = 7.70 mm
Crop factor =   43.27  = 5.62
7.70

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

SD1000 equivalent aperture

Crop factor = 6.02
Aperture = f2.8 - f4.9

35-mm equivalent aperture = (f2.8 - f4.9) × 6.02 = f16.9 - f29.5

ELPH 300 HS equivalent aperture

Crop factor = 5.62
Aperture = f2.7 - f5.9

35-mm equivalent aperture = (f2.7 - f5.9) × 5.62 = f15.2 - f33.2

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.