Canon PowerShot SD1100 IS vs. Canon PowerShot SD1400 IS

Comparison

change cameras »
PowerShot SD1100 IS image
vs
PowerShot SD1400 IS image
Canon PowerShot SD1100 IS Canon PowerShot SD1400 IS
check price » check price »
Megapixels
8.00
14.10
Max. image resolution
3264 x 2448
4320 x 3240

Sensor

Sensor type
CCD
CCD
Sensor size
1/2.5" (~ 5.75 x 4.32 mm)
1/2.3" (~ 6.16 x 4.62 mm)
Sensor resolution
3262 x 2453
4330 x 3256
Diagonal
7.19 mm
7.70 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1 : 1.15
(ratio)
Canon PowerShot SD1100 IS Canon PowerShot SD1400 IS
Surface area:
24.84 mm² vs 28.46 mm²
Difference: 3.62 mm² (15%)
SD1400 IS sensor is approx. 1.15x bigger than SD1100 IS sensor.
Note: You are comparing cameras of different generations. There is a 2 year gap between Canon SD1100 IS (2008) and Canon SD1400 IS (2010). All things being equal, newer sensor generations generally outperform the older.
Pixel pitch
1.76 µm
1.42 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 0.34 µm (24%)
Pixel pitch of SD1100 IS is approx. 24% higher than pixel pitch of SD1400 IS.
Pixel area
3.1 µm²
2.02 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 1.08 µm² (53%)
A pixel on Canon SD1100 IS sensor is approx. 53% bigger than a pixel on Canon SD1400 IS.
Pixel density
32.18 MP/cm²
49.41 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 17.23 µm (54%)
Canon SD1400 IS has approx. 54% higher pixel density than Canon SD1100 IS.
To learn about the accuracy of these numbers, click here.



Specs

Canon SD1100 IS
Canon SD1400 IS
Crop factor
6.02
5.62
Total megapixels
8.30
14.50
Effective megapixels
8.00
14.10
Optical zoom
3x
4x
Digital zoom
Yes
Yes
ISO sensitivity
Auto, 80, 100, 200, 400, 800, 1600
Auto, 80, 100, 200, 400, 800, 1600
RAW
Manual focus
Normal focus range
30 cm
50 cm
Macro focus range
3 cm
3 cm
Focal length (35mm equiv.)
38 - 114 mm
28 - 112 mm
Aperture priority
No
No
Max. aperture
f2.8 - f4.9
f2.8 - f5.9
Max. aperture (35mm equiv.)
f16.9 - f29.5
f15.7 - f33.2
Metering
Multi, Center-weighted, Spot
Centre weighted, Evaluative, Spot
Exposure compensation
±2 EV (in 1/3 EV steps)
±2 EV (in 1/3 EV steps)
Shutter priority
No
No
Min. shutter speed
15 sec
15 sec
Max. shutter speed
1/1500 sec
1/1500 sec
Built-in flash
External flash
Viewfinder
Optical (tunnel)
None
White balance presets
5
5
Screen size
2.5"
2.7"
Screen resolution
230,000 dots
230,000 dots
Video capture
Max. video resolution
Storage types
SD/SDHC/MMC Card
SDHC, SDXC, Secure Digital
USB
USB 2.0 (480 Mbit/sec)
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
NB-4L Li-ion battery
Lithium-Ion NB-4L battery
Weight
165 g
133 g
Dimensions
87 x 55 x 22 mm
92.2 x 56.1 x 17.8 mm
Year
2008
2010




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Canon SD1100 IS diagonal

The diagonal of SD1100 IS sensor is not 1/2.5 or 0.4" (10.2 mm) as you might expect, but approximately two thirds of that value - 7.19 mm. If you want to know why, see sensor sizes.

w = 5.75 mm
h = 4.32 mm
Diagonal =  5.75² + 4.32²   = 7.19 mm

Canon SD1400 IS diagonal

The diagonal of SD1400 IS sensor is not 1/2.3 or 0.43" (11 mm) as you might expect, but approximately two thirds of that value - 7.7 mm. If you want to know why, see sensor sizes.

w = 6.16 mm
h = 4.62 mm
Diagonal =  6.16² + 4.62²   = 7.70 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

SD1100 IS sensor area

Width = 5.75 mm
Height = 4.32 mm

Surface area = 5.75 × 4.32 = 24.84 mm²

SD1400 IS sensor area

Width = 6.16 mm
Height = 4.62 mm

Surface area = 6.16 × 4.62 = 28.46 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

SD1100 IS pixel pitch

Sensor width = 5.75 mm
Sensor resolution width = 3262 pixels
Pixel pitch =   5.75  × 1000  = 1.76 µm
3262

SD1400 IS pixel pitch

Sensor width = 6.16 mm
Sensor resolution width = 4330 pixels
Pixel pitch =   6.16  × 1000  = 1.42 µm
4330


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

SD1100 IS pixel area

Pixel pitch = 1.76 µm

Pixel area = 1.76² = 3.1 µm²

SD1400 IS pixel area

Pixel pitch = 1.42 µm

Pixel area = 1.42² = 2.02 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

SD1100 IS pixel density

Sensor resolution width = 3262 pixels
Sensor width = 0.575 cm

Pixel density = (3262 / 0.575)² / 1000000 = 32.18 MP/cm²

SD1400 IS pixel density

Sensor resolution width = 4330 pixels
Sensor width = 0.616 cm

Pixel density = (4330 / 0.616)² / 1000000 = 49.41 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

SD1100 IS sensor resolution

Sensor width = 5.75 mm
Sensor height = 4.32 mm
Effective megapixels = 8.00
r = 5.75/4.32 = 1.33
X =  8.00 × 1000000  = 2453
1.33
Resolution horizontal: X × r = 2453 × 1.33 = 3262
Resolution vertical: X = 2453

Sensor resolution = 3262 x 2453

SD1400 IS sensor resolution

Sensor width = 6.16 mm
Sensor height = 4.62 mm
Effective megapixels = 14.10
r = 6.16/4.62 = 1.33
X =  14.10 × 1000000  = 3256
1.33
Resolution horizontal: X × r = 3256 × 1.33 = 4330
Resolution vertical: X = 3256

Sensor resolution = 4330 x 3256


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


SD1100 IS crop factor

Sensor diagonal in mm = 7.19 mm
Crop factor =   43.27  = 6.02
7.19

SD1400 IS crop factor

Sensor diagonal in mm = 7.70 mm
Crop factor =   43.27  = 5.62
7.70

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

SD1100 IS equivalent aperture

Crop factor = 6.02
Aperture = f2.8 - f4.9

35-mm equivalent aperture = (f2.8 - f4.9) × 6.02 = f16.9 - f29.5

SD1400 IS equivalent aperture

Crop factor = 5.62
Aperture = f2.8 - f5.9

35-mm equivalent aperture = (f2.8 - f5.9) × 5.62 = f15.7 - f33.2

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.