Fujifilm FinePix S7000 Zoom vs. Fujifilm FinePix S100fs

Comparison

change cameras »

Fujifilm FinePix S7000 Zoom

Fujifilm FinePix S100fs

check price »

Megapixels

6.00

11.10

Max. image resolution

4048 x 3040

3840 x 2880

Sensor

Sensor type

CCD

Sensor size

1/1.7" (~ 7.53 x 5.64 mm)

2/3" (~ 8.8 x 6.6 mm)

Sensor resolution

2835 x 2116

3842 x 2889

Diagonal

9.41 mm

11.00 mm

Sensor size comparison

Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »

	vs
1	:	1.37
(ratio)

Fujifilm FinePix S7000 Zoom		Fujifilm FinePix S100fs

Surface area:

42.47 mm²

58.08 mm²

Difference: 15.61 mm² (37%)

S100fs sensor is approx. 1.37x bigger than S7000 Zoom sensor.

Note: You are comparing cameras of different generations. There is a 5 year gap between Fujifilm S7000 Zoom (2003) and Fujifilm S100fs (2008). All things being equal, newer sensor generations generally outperform the older.

Pixel pitch

2.66 µm

2.29 µm

Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.

Difference: 0.37 µm (16%)

Pixel pitch of S7000 Zoom is approx. 16% higher than pixel pitch of S100fs.

Pixel area

7.08 µm²

5.24 µm²

Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.

Relative pixel sizes:

Pixel area difference: 1.84 µm² (35%)

A pixel on Fujifilm S7000 Zoom sensor is approx. 35% bigger than a pixel on Fujifilm S100fs.

Pixel density

14.17 MP/cm²

19.06 MP/cm²

Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.

Difference: 4.89 µm (35%)

Fujifilm S100fs has approx. 35% higher pixel density than Fujifilm S7000 Zoom.

To learn about the accuracy of these numbers, click here.

Specs

Fujifilm S7000 Zoom

Fujifilm S100fs

Crop factor

4.6

3.93

Total megapixels

6.30

Effective megapixels

6.00

11.10

Optical zoom

14.3x

Digital zoom

Yes

ISO sensitivity

Auto, 200, 400 (higher from 3mp down)

Auto, 64, 100, 200, 400, 800, 1600, 3200 (6400 at 6MP, 10000 at 3MP)

RAW

Manual focus

Normal focus range

50 cm

Macro focus range

1 cm

2 cm

Focal length (35mm equiv.)

35 - 210 mm

28 - 400 mm

Aperture priority

Yes

Max. aperture

f2.8 - f3.1

f2.8 - f5.3

Max. aperture (35mm equiv.)

f12.9 - f14.3

f11 - f20.8

Metering

Multi, Average, Spot

256-segment Matrix

Exposure compensation

±2 EV (in 1/3 EV steps)

Shutter priority

Yes

Min. shutter speed

15 sec

30 sec

Max. shutter speed

1/10000 sec

1/4000 sec

Built-in flash

External flash

Viewfinder

Electronic

White balance presets

Screen size

1.8"

2.5"

Screen resolution

118,000 dots

230,000 dots

Video capture

Max. video resolution

Storage types

xD Picture Card, Compact Flash Type I or II

SDHC, Secure Digital, xD Picture card

USB

USB 2.0 (480 Mbit/sec)

HDMI

Wireless

GPS

Battery

AA NiMH (4) batteries included

NP-140 Li-ion battery

Weight

590 g

950 g

Dimensions

121 x 82 x 97 mm

133 x 94 x 150 mm

Year

2003

2008

Choose cameras to compare

Popular comparisons:

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:

Diagonal = √

w² + h²

where w = sensor width and h = sensor height

Fujifilm S7000 Zoom diagonal

The diagonal of S7000 Zoom sensor is not 1/1.7 or 0.59" (14.9 mm) as you might expect, but approximately two thirds of that value - 9.41 mm. If you want to know why, see sensor sizes.

w = 7.53 mm
h = 5.64 mm

Diagonal = √

7.53² + 5.64²

= 9.41 mm

Fujifilm S100fs diagonal

The diagonal of S100fs sensor is not 2/3 or 0.67" (16.9 mm) as you might expect, but approximately two thirds of that value - 11 mm. If you want to know why, see sensor sizes.

w = 8.80 mm
h = 6.60 mm

Diagonal = √

8.80² + 6.60²

= 11.00 mm

Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

S7000 Zoom sensor area

Width = 7.53 mm
Height = 5.64 mm

Surface area = 7.53 × 5.64 = 42.47 mm²

S100fs sensor area

Width = 8.80 mm
Height = 6.60 mm

Surface area = 8.80 × 6.60 = 58.08 mm²

Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:

Pixel pitch =	sensor width in mm	× 1000
	sensor resolution width in pixels

S7000 Zoom pixel pitch

Sensor width = 7.53 mm
Sensor resolution width = 2835 pixels

Pixel pitch =	7.53	× 1000	= 2.66 µm
	2835

S100fs pixel pitch

Sensor width = 8.80 mm
Sensor resolution width = 3842 pixels

Pixel pitch =	8.80	× 1000	= 2.29 µm
	3842

Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:

Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:

Pixel area =	sensor surface area in mm²
	effective megapixels

S7000 Zoom pixel area

Pixel pitch = 2.66 µm

Pixel area = 2.66² = 7.08 µm²

S100fs pixel area

Pixel pitch = 2.29 µm

Pixel area = 2.29² = 5.24 µm²

Pixel density

Pixel density can be calculated with the following formula:

Pixel density = (	sensor resolution width in pixels	)² / 1000000
	sensor width in cm

One could also use this formula:

Pixel density =	effective megapixels × 1000000	/ 10000
	sensor surface area in mm²

S7000 Zoom pixel density

Sensor resolution width = 2835 pixels
Sensor width = 0.753 cm

Pixel density = (2835 / 0.753)² / 1000000 = 14.17 MP/cm²

S100fs pixel density

Sensor resolution width = 3842 pixels
Sensor width = 0.88 cm

Pixel density = (3842 / 0.88)² / 1000000 = 19.06 MP/cm²

Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:

(X × r) × X = effective megapixels × 1000000 →

X = √	effective megapixels × 1000000
	r

3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

S7000 Zoom sensor resolution

Sensor width = 7.53 mm
Sensor height = 5.64 mm
Effective megapixels = 6.00

r = 7.53/5.64 = 1.34

X = √	6.00 × 1000000	= 2116
	1.34

Resolution horizontal: X × r = 2116 × 1.34 = 2835
Resolution vertical: X = 2116

Sensor resolution = 2835 x 2116

S100fs sensor resolution

Sensor width = 8.80 mm
Sensor height = 6.60 mm
Effective megapixels = 11.10

r = 8.80/6.60 = 1.33

X = √	11.10 × 1000000	= 2889
	1.33

Resolution horizontal: X × r = 2889 × 1.33 = 3842
Resolution vertical: X = 2889

Sensor resolution = 3842 x 2889

Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.

Crop factor =	43.27 mm
	sensor diagonal in mm

S7000 Zoom crop factor

Sensor diagonal in mm = 9.41 mm

Crop factor =	43.27	= 4.6
	9.41

S100fs crop factor

Sensor diagonal in mm = 11.00 mm

Crop factor =	43.27	= 3.93
	11.00

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

S7000 Zoom equivalent aperture

Crop factor = 4.6
Aperture = f2.8 - f3.1

35-mm equivalent aperture = (f2.8 - f3.1) × 4.6 = f12.9 - f14.3

S100fs equivalent aperture

Crop factor = 3.93
Aperture = f2.8 - f5.3

35-mm equivalent aperture = (f2.8 - f5.3) × 3.93 = f11 - f20.8

More comparisons of Fujifilm S7000 Zoom:

Enter your screen size (diagonal)

My screen size is inches

Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.