Fujifilm X-Pro3 vs. Canon EOS 5D Mark IV

Comparison

change cameras »
X-Pro3 image
vs
EOS 5D Mark IV image
Fujifilm X-Pro3 Canon EOS 5D Mark IV
check price » check price »
Megapixels
26.10
30.10
Max. image resolution
6240 x 4160
6720 x 4480

Sensor

Sensor type
CMOS
CMOS
Sensor size
23.5 x 15.6 mm
36 x 24 mm
Sensor resolution
6277 x 4157
6720 x 4480
Diagonal
28.21 mm
43.27 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1 : 2.36
(ratio)
Fujifilm X-Pro3 Canon EOS 5D Mark IV
Surface area:
366.60 mm² vs 864.00 mm²
Difference: 497.4 mm² (136%)
5D Mark IV sensor is approx. 2.36x bigger than X-Pro3 sensor.
Note: You are comparing cameras of different generations. There is a 3 year gap between Fujifilm X-Pro3 (2019) and Canon 5D Mark IV (2016). All things being equal, newer sensor generations generally outperform the older.
Pixel pitch
3.74 µm
5.36 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 1.62 µm (43%)
Pixel pitch of 5D Mark IV is approx. 43% higher than pixel pitch of X-Pro3.
Pixel area
13.99 µm²
28.73 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 14.74 µm² (105%)
A pixel on Canon 5D Mark IV sensor is approx. 105% bigger than a pixel on Fujifilm X-Pro3.
Pixel density
7.13 MP/cm²
3.48 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 3.65 µm (105%)
Fujifilm X-Pro3 has approx. 105% higher pixel density than Canon 5D Mark IV.
To learn about the accuracy of these numbers, click here.



Specs

Fujifilm X-Pro3
Canon 5D Mark IV
Crop factor
1.53
1
Total megapixels
31.70
Effective megapixels
26.10
30.10
Optical zoom
 
 
Digital zoom
ISO sensitivity
Auto, 160-12800 (extendable to 80-51200)
Auto, 100-32000 (expandable to 50-102400)
RAW
Manual focus
Normal focus range
Macro focus range
Focal length (35mm equiv.)
Aperture priority
Yes
Yes
Max. aperture
Max. aperture (35mm equiv.)
n/a
n/a
Metering
Multi, Center-weighted, Average, Spot
Multi, Center-weighted, Spot, Partial
Exposure compensation
±5 EV (in 1/3 EV steps)
±5 EV (in 1/3 EV, 1/2 EV steps)
Shutter priority
Yes
Yes
Min. shutter speed
30 sec
30 sec
Max. shutter speed
1/32000 sec
1/8000 sec
Built-in flash
External flash
Viewfinder
Electronic and Optical (tunnel)
Optical (pentaprism)
White balance presets
7
6
Screen size
3"
3.2"
Screen resolution
1,620,000 dots
1,620,000 dots
Video capture
Max. video resolution
4096x2160 (30p/​25p/​24p)
4096x2160 (30p/25p/24p)
Storage types
SD/SDHC/SDXC
SD/SDHC/SDXC/CompactFlash
USB
USB 3.0 (5 GBit/sec)
USB 3.0 (5 GBit/sec)
HDMI
Wireless
GPS
Battery
NP-W126S lithium-ion battery
LP-E6N lithium-ion battery
Weight
497 g
890 g
Dimensions
140.5 x 82.8 x 46.1 mm
150.7 x 116.4 x 75.9 mm
Year
2019
2016




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Fujifilm X-Pro3 diagonal

w = 23.50 mm
h = 15.60 mm
Diagonal =  23.50² + 15.60²   = 28.21 mm

Canon 5D Mark IV diagonal

w = 36.00 mm
h = 24.00 mm
Diagonal =  36.00² + 24.00²   = 43.27 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

X-Pro3 sensor area

Width = 23.50 mm
Height = 15.60 mm

Surface area = 23.50 × 15.60 = 366.60 mm²

5D Mark IV sensor area

Width = 36.00 mm
Height = 24.00 mm

Surface area = 36.00 × 24.00 = 864.00 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

X-Pro3 pixel pitch

Sensor width = 23.50 mm
Sensor resolution width = 6277 pixels
Pixel pitch =   23.50  × 1000  = 3.74 µm
6277

5D Mark IV pixel pitch

Sensor width = 36.00 mm
Sensor resolution width = 6720 pixels
Pixel pitch =   36.00  × 1000  = 5.36 µm
6720


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

X-Pro3 pixel area

Pixel pitch = 3.74 µm

Pixel area = 3.74² = 13.99 µm²

5D Mark IV pixel area

Pixel pitch = 5.36 µm

Pixel area = 5.36² = 28.73 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

X-Pro3 pixel density

Sensor resolution width = 6277 pixels
Sensor width = 2.35 cm

Pixel density = (6277 / 2.35)² / 1000000 = 7.13 MP/cm²

5D Mark IV pixel density

Sensor resolution width = 6720 pixels
Sensor width = 3.6 cm

Pixel density = (6720 / 3.6)² / 1000000 = 3.48 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

X-Pro3 sensor resolution

Sensor width = 23.50 mm
Sensor height = 15.60 mm
Effective megapixels = 26.10
r = 23.50/15.60 = 1.51
X =  26.10 × 1000000  = 4157
1.51
Resolution horizontal: X × r = 4157 × 1.51 = 6277
Resolution vertical: X = 4157

Sensor resolution = 6277 x 4157

5D Mark IV sensor resolution

Sensor width = 36.00 mm
Sensor height = 24.00 mm
Effective megapixels = 30.10
r = 36.00/24.00 = 1.5
X =  30.10 × 1000000  = 4480
1.5
Resolution horizontal: X × r = 4480 × 1.5 = 6720
Resolution vertical: X = 4480

Sensor resolution = 6720 x 4480


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


X-Pro3 crop factor

Sensor diagonal in mm = 28.21 mm
Crop factor =   43.27  = 1.53
28.21

5D Mark IV crop factor

Sensor diagonal in mm = 43.27 mm
Crop factor =   43.27  = 1
43.27

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

X-Pro3 equivalent aperture

Aperture is a lens characteristic, so it's calculated only for fixed lens cameras. If you want to know the equivalent aperture for Fujifilm X-Pro3, take the aperture of the lens you're using and multiply it with crop factor.

Crop factor for Fujifilm X-Pro3 is 1.53

5D Mark IV equivalent aperture

Aperture is a lens characteristic, so it's calculated only for fixed lens cameras. If you want to know the equivalent aperture for Canon 5D Mark IV, take the aperture of the lens you're using and multiply it with crop factor.

Since crop factor for Canon 5D Mark IV is 1, the equivalent aperture is aperture.

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.