Fujifilm XF1 vs. Canon PowerShot S110

Comparison

change cameras »
XF1 image
vs
PowerShot S110 image
Fujifilm XF1 Canon PowerShot S110
check price » check price »
Megapixels
12.00
12.10
Max. image resolution
4000 x 3000
4000 x 3000

Sensor

Sensor type
CMOS
CMOS
Sensor size
2/3" (~ 8.8 x 6.6 mm)
1/1.7" (~ 7.53 x 5.64 mm)
Sensor resolution
3995 x 3004
4027 x 3005
Diagonal
11.00 mm
9.41 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1.37 : 1
(ratio)
Fujifilm XF1 Canon PowerShot S110
Surface area:
58.08 mm² vs 42.47 mm²
Difference: 15.61 mm² (37%)
XF1 sensor is approx. 1.37x bigger than S110 sensor.
Pixel pitch
2.2 µm
1.87 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 0.33 µm (18%)
Pixel pitch of XF1 is approx. 18% higher than pixel pitch of S110.
Pixel area
4.84 µm²
3.5 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 1.34 µm² (38%)
A pixel on Fujifilm XF1 sensor is approx. 38% bigger than a pixel on Canon S110.
Pixel density
20.61 MP/cm²
28.6 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 7.99 µm (39%)
Canon S110 has approx. 39% higher pixel density than Fujifilm XF1.
To learn about the accuracy of these numbers, click here.



Specs

Fujifilm XF1
Canon S110
Crop factor
3.93
4.6
Total megapixels
13.30
Effective megapixels
12.00
12.10
Optical zoom
4x
5x
Digital zoom
No
Yes
ISO sensitivity
Auto, 100 - 3200, (4000, 5000, 6400, 12800 with boost)
Auto, 80 - 12800
RAW
Manual focus
Normal focus range
50 cm
30 cm
Macro focus range
3 cm
3 cm
Focal length (35mm equiv.)
25 - 100 mm
24 - 120 mm
Aperture priority
Yes
Yes
Max. aperture
f1.8 - f4.9
f2.0 - f5.9
Max. aperture (35mm equiv.)
f7.1 - f19.3
f9.2 - f27.1
Metering
Multi, Average, Spot
Multi, Center-weighted, Spot
Exposure compensation
±2 EV (in 1/3 EV steps)
±3 EV (in 1/3 EV steps)
Shutter priority
Yes
Yes
Min. shutter speed
30 sec
15 sec
Max. shutter speed
1/4000 sec
1/2000 sec
Built-in flash
External flash
Viewfinder
None
None
White balance presets
7
7
Screen size
3"
3"
Screen resolution
460,000 dots
461,000 dots
Video capture
Max. video resolution
1920x1080 (24p)
Storage types
SD/SDHC/SDXC
SD/SDHC/SDXC
USB
USB 2.0 (480 Mbit/sec)
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
Lithium-Ion NP-50 rechargeable battery
Lithium-Ion NB-5L rechargeable battery
Weight
255 g
198 g
Dimensions
107.9 x 61.5 x 33.0 mm
98.8 x 59 x 26.9 mm
Year
2012
2012




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Fujifilm XF1 diagonal

The diagonal of XF1 sensor is not 2/3 or 0.67" (16.9 mm) as you might expect, but approximately two thirds of that value - 11 mm. If you want to know why, see sensor sizes.

w = 8.80 mm
h = 6.60 mm
Diagonal =  8.80² + 6.60²   = 11.00 mm

Canon S110 diagonal

The diagonal of S110 sensor is not 1/1.7 or 0.59" (14.9 mm) as you might expect, but approximately two thirds of that value - 9.41 mm. If you want to know why, see sensor sizes.

w = 7.53 mm
h = 5.64 mm
Diagonal =  7.53² + 5.64²   = 9.41 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

XF1 sensor area

Width = 8.80 mm
Height = 6.60 mm

Surface area = 8.80 × 6.60 = 58.08 mm²

S110 sensor area

Width = 7.53 mm
Height = 5.64 mm

Surface area = 7.53 × 5.64 = 42.47 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

XF1 pixel pitch

Sensor width = 8.80 mm
Sensor resolution width = 3995 pixels
Pixel pitch =   8.80  × 1000  = 2.2 µm
3995

S110 pixel pitch

Sensor width = 7.53 mm
Sensor resolution width = 4027 pixels
Pixel pitch =   7.53  × 1000  = 1.87 µm
4027


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

XF1 pixel area

Pixel pitch = 2.2 µm

Pixel area = 2.2² = 4.84 µm²

S110 pixel area

Pixel pitch = 1.87 µm

Pixel area = 1.87² = 3.5 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

XF1 pixel density

Sensor resolution width = 3995 pixels
Sensor width = 0.88 cm

Pixel density = (3995 / 0.88)² / 1000000 = 20.61 MP/cm²

S110 pixel density

Sensor resolution width = 4027 pixels
Sensor width = 0.753 cm

Pixel density = (4027 / 0.753)² / 1000000 = 28.6 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

XF1 sensor resolution

Sensor width = 8.80 mm
Sensor height = 6.60 mm
Effective megapixels = 12.00
r = 8.80/6.60 = 1.33
X =  12.00 × 1000000  = 3004
1.33
Resolution horizontal: X × r = 3004 × 1.33 = 3995
Resolution vertical: X = 3004

Sensor resolution = 3995 x 3004

S110 sensor resolution

Sensor width = 7.53 mm
Sensor height = 5.64 mm
Effective megapixels = 12.10
r = 7.53/5.64 = 1.34
X =  12.10 × 1000000  = 3005
1.34
Resolution horizontal: X × r = 3005 × 1.34 = 4027
Resolution vertical: X = 3005

Sensor resolution = 4027 x 3005


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


XF1 crop factor

Sensor diagonal in mm = 11.00 mm
Crop factor =   43.27  = 3.93
11.00

S110 crop factor

Sensor diagonal in mm = 9.41 mm
Crop factor =   43.27  = 4.6
9.41

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

XF1 equivalent aperture

Crop factor = 3.93
Aperture = f1.8 - f4.9

35-mm equivalent aperture = (f1.8 - f4.9) × 3.93 = f7.1 - f19.3

S110 equivalent aperture

Crop factor = 4.6
Aperture = f2.0 - f5.9

35-mm equivalent aperture = (f2.0 - f5.9) × 4.6 = f9.2 - f27.1

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.