Jenoptik JD 4.1 zoom vs. Kyocera Finecam M410R
Comparison
| change cameras » | |||||
|
vs |
|
|||
| Jenoptik JD 4.1 zoom | Kyocera Finecam M410R | ||||
| check price » | check price » | ||||
Megapixels
4.00
4.00
Max. image resolution
2592 x 1944
2272 x 1704
Sensor
Sensor type
CCD
CCD
Sensor size
1/2.5" (~ 5.75 x 4.32 mm)
1/2.7" (~ 5.33 x 4 mm)
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera.
Sensors can vary greatly in size. As a general rule, the bigger the
sensor, the better the image quality.
Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.
Learn more about sensor sizes »
Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.
Learn more about sensor sizes »
Actual sensor size
Note: Actual size is set to screen → change »
|
|
vs |
|
| 1.17 | : | 1 |
| (ratio) | ||
| Jenoptik JD 4.1 zoom | Kyocera Finecam M410R | |
Surface area:
| 24.84 mm² | vs | 21.32 mm² |
Difference: 3.52 mm² (17%)
JD 4.1 zoom sensor is approx. 1.17x bigger than M410R sensor.
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.
The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Pixel or photosite area affects how much light per pixel can be gathered.
The larger it is the more light can be collected by a single pixel.
Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 0.86 µm² (16%)
A pixel on Jenoptik JD 4.1 zoom sensor is approx. 16% bigger than a pixel on Kyocera M410R.
Pixel density tells you how many million pixels fit or would fit in one
square cm of the sensor.
Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Higher pixel density means smaller pixels and lower pixel density means larger pixels.
To learn about the accuracy of these numbers,
click here.
Specs
Jenoptik JD 4.1 zoom
Kyocera M410R
Total megapixels
Effective megapixels
Optical zoom
Yes
10x
Digital zoom
Yes
Yes
ISO sensitivity
100
Auto, 100, 200, 400, 800
RAW
Manual focus
Normal focus range
50 cm
60 cm
Macro focus range
10 cm
10 cm
Focal length (35mm equiv.)
37 - 105 mm
37 - 370 mm
Aperture priority
No
No
Max. aperture
f2.9 - f5
f2.8 - f3.1
Metering
Multi-segment, Spot
Exposure compensation
±2 EV (in 1/3 EV steps)
±2 EV (in 1/3 EV steps)
Shutter priority
No
No
Min. shutter speed
8 sec
1 sec
Max. shutter speed
1/2000 sec
1/2000 sec
Built-in flash
External flash
Viewfinder
Optical
Electronic
White balance presets
4
6
Screen size
1.5"
1.5"
Screen resolution
110,000 dots
Video capture
Max. video resolution
Storage types
Secure Digital
MultiMedia, Secure Digital
USB
USB 1.1
USB 1.0
HDMI
Wireless
GPS
Battery
2x AA
AA (4) batteries (NiMH recommended)
Weight
150 g
290 g
Dimensions
106 x 33,5 x 55,6 mm
107 x 73 x 64 mm
Year
2004
2004
Choose cameras to compare
Popular comparisons:
- Jenoptik JD 4.1 zoom vs. Jenoptik JD 4.1 z8
- Jenoptik JD 4.1 zoom vs. Jenoptik JD 4100 z3 S
- Jenoptik JD 4.1 zoom vs. Nikon Coolpix S570
- Jenoptik JD 4.1 zoom vs. Canon Digital IXUS 110 IS
- Jenoptik JD 4.1 zoom vs. Samsung ES10
- Jenoptik JD 4.1 zoom vs. Nikon Coolpix S3000
- Jenoptik JD 4.1 zoom vs. Canon PowerShot A800
- Jenoptik JD 4.1 zoom vs. Panasonic Lumix DMC-FX30
- Jenoptik JD 4.1 zoom vs. Kodak DC260
- Jenoptik JD 4.1 zoom vs. Samsung ST50
- Jenoptik JD 4.1 zoom vs. Kyocera Finecam M410R
Diagonal
Diagonal is calculated by the use of Pythagorean theorem:
where w = sensor width and h = sensor height
| Diagonal = √ | w² + h² |
Jenoptik JD 4.1 zoom diagonal
The diagonal of JD 4.1 zoom sensor is not 1/2.5 or 0.4" (10.2 mm) as you might expect, but approximately two thirds of
that value - 7.19 mm. If you want to know why, see
sensor sizes.
w = 5.75 mm
h = 4.32 mm
w = 5.75 mm
h = 4.32 mm
| Diagonal = √ | 5.75² + 4.32² | = 7.19 mm |
Kyocera M410R diagonal
The diagonal of M410R sensor is not 1/2.7 or 0.37" (9.4 mm) as you might expect, but approximately two thirds of
that value - 6.66 mm. If you want to know why, see
sensor sizes.
w = 5.33 mm
h = 4.00 mm
w = 5.33 mm
h = 4.00 mm
| Diagonal = √ | 5.33² + 4.00² | = 6.66 mm |
Surface area
Surface area is calculated by multiplying the width and the height of a sensor.
JD 4.1 zoom sensor area
Width = 5.75 mm
Height = 4.32 mm
Surface area = 5.75 × 4.32 = 24.84 mm²
Height = 4.32 mm
Surface area = 5.75 × 4.32 = 24.84 mm²
M410R sensor area
Width = 5.33 mm
Height = 4.00 mm
Surface area = 5.33 × 4.00 = 21.32 mm²
Height = 4.00 mm
Surface area = 5.33 × 4.00 = 21.32 mm²
Pixel pitch
Pixel pitch is the distance from the center of one pixel to the center of the
next measured in micrometers (µm). It can be calculated with the following formula:
| Pixel pitch = | sensor width in mm | × 1000 |
| sensor resolution width in pixels |
JD 4.1 zoom pixel pitch
Sensor width = 5.75 mm
Sensor resolution width = 2306 pixels
Sensor resolution width = 2306 pixels
| Pixel pitch = | 5.75 | × 1000 | = 2.49 µm |
| 2306 |
M410R pixel pitch
Sensor width = 5.33 mm
Sensor resolution width = 2306 pixels
Sensor resolution width = 2306 pixels
| Pixel pitch = | 5.33 | × 1000 | = 2.31 µm |
| 2306 |
Pixel area
The area of one pixel can be calculated by simply squaring the pixel pitch:
You could also divide sensor surface area with effective megapixels:
Pixel area = pixel pitch²
You could also divide sensor surface area with effective megapixels:
| Pixel area = | sensor surface area in mm² |
| effective megapixels |
JD 4.1 zoom pixel area
Pixel pitch = 2.49 µm
Pixel area = 2.49² = 6.2 µm²
Pixel area = 2.49² = 6.2 µm²
M410R pixel area
Pixel pitch = 2.31 µm
Pixel area = 2.31² = 5.34 µm²
Pixel area = 2.31² = 5.34 µm²
Pixel density
Pixel density can be calculated with the following formula:
One could also use this formula:
| Pixel density = ( | sensor resolution width in pixels | )² / 1000000 |
| sensor width in cm |
One could also use this formula:
| Pixel density = | effective megapixels × 1000000 | / 10000 |
| sensor surface area in mm² |
JD 4.1 zoom pixel density
Sensor resolution width = 2306 pixels
Sensor width = 0.575 cm
Pixel density = (2306 / 0.575)² / 1000000 = 16.08 MP/cm²
Sensor width = 0.575 cm
Pixel density = (2306 / 0.575)² / 1000000 = 16.08 MP/cm²
M410R pixel density
Sensor resolution width = 2306 pixels
Sensor width = 0.533 cm
Pixel density = (2306 / 0.533)² / 1000000 = 18.72 MP/cm²
Sensor width = 0.533 cm
Pixel density = (2306 / 0.533)² / 1000000 = 18.72 MP/cm²
Sensor resolution
Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher
than maximum (not interpolated) image resolution which is usually stated on camera specifications.
Sensor resolution is used in pixel pitch, pixel area, and pixel density formula.
For sake of simplicity, we're going to calculate it in 3 stages.
1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.
2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
3. To get sensor resolution we then multiply X with the corresponding ratio:
Resolution horizontal: X × r
Resolution vertical: X
1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.
2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
| (X × r) × X = effective megapixels × 1000000 → |
|
Resolution horizontal: X × r
Resolution vertical: X
JD 4.1 zoom sensor resolution
Sensor width = 5.75 mm
Sensor height = 4.32 mm
Effective megapixels = 4.00
Resolution horizontal: X × r = 1734 × 1.33 = 2306
Resolution vertical: X = 1734
Sensor resolution = 2306 x 1734
Sensor height = 4.32 mm
Effective megapixels = 4.00
| r = 5.75/4.32 = 1.33 |
|
Resolution vertical: X = 1734
Sensor resolution = 2306 x 1734
M410R sensor resolution
Sensor width = 5.33 mm
Sensor height = 4.00 mm
Effective megapixels = 4.00
Resolution horizontal: X × r = 1734 × 1.33 = 2306
Resolution vertical: X = 1734
Sensor resolution = 2306 x 1734
Sensor height = 4.00 mm
Effective megapixels = 4.00
| r = 5.33/4.00 = 1.33 |
|
Resolution vertical: X = 1734
Sensor resolution = 2306 x 1734
Crop factor
Crop factor or focal length multiplier is calculated by dividing the diagonal
of 35 mm film (43.27 mm) with the diagonal of the sensor.
| Crop factor = | 43.27 mm |
| sensor diagonal in mm |
JD 4.1 zoom crop factor
Sensor diagonal in mm = 7.19 mm
| Crop factor = | 43.27 | = 6.02 |
| 7.19 |
M410R crop factor
Sensor diagonal in mm = 6.66 mm
| Crop factor = | 43.27 | = 6.5 |
| 6.66 |
35 mm equivalent aperture
Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture
with crop factor (a.k.a. focal length multiplier).
JD 4.1 zoom equivalent aperture
Crop factor = 6.02
Aperture = f2.9 - f5
35-mm equivalent aperture = (f2.9 - f5) × 6.02 = f17.5 - f30.1
Aperture = f2.9 - f5
35-mm equivalent aperture = (f2.9 - f5) × 6.02 = f17.5 - f30.1
M410R equivalent aperture
Crop factor = 6.5
Aperture = f2.8 - f3.1
35-mm equivalent aperture = (f2.8 - f3.1) × 6.5 = f18.2 - f20.2
Aperture = f2.8 - f3.1
35-mm equivalent aperture = (f2.8 - f3.1) × 6.5 = f18.2 - f20.2
Enter your screen size (diagonal)
My screen size is
inches
Actual size is currently adjusted to screen.
If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.
If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.