Kodak EasyShare CX7525 vs. Kodak EasyShare CX7430

Comparison

change cameras »

Kodak EasyShare CX7525

Kodak EasyShare CX7430

check price »

Megapixels

4.23

4.00

Max. image resolution

2576 x 1932

2304 x 1728

Sensor

Sensor type

CCD

Sensor size

1/2.5" (~ 5.75 x 4.32 mm)

Sensor resolution

2371 x 1783

2306 x 1734

Diagonal

7.19 mm

Sensor size comparison

Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »

	vs
1	:	1
(ratio)

Kodak EasyShare CX7525		Kodak EasyShare CX7430

Surface area:

24.84 mm²

Difference: 0 mm² (0%)

CX7525 and CX7430 sensors are the same size.

Pixel pitch

2.43 µm

2.49 µm

Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.

Difference: 0.06 µm (2%)

Pixel pitch of CX7430 is approx. 2% higher than pixel pitch of CX7525.

Pixel area

5.9 µm²

6.2 µm²

Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.

Relative pixel sizes:

Pixel area difference: 0.3 µm² (5%)

A pixel on Kodak CX7430 sensor is approx. 5% bigger than a pixel on Kodak CX7525.

Pixel density

17 MP/cm²

16.08 MP/cm²

Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.

Difference: 0.92 µm (6%)

Kodak CX7525 has approx. 6% higher pixel density than Kodak CX7430.

To learn about the accuracy of these numbers, click here.

Specs

Kodak CX7525

Kodak CX7430

Crop factor

6.02

Total megapixels

4.20

Effective megapixels

4.00

Optical zoom

Yes

Digital zoom

Yes

ISO sensitivity

Auto, 80, 100, 160, 200, 400

Auto, 80, 160, 200, 400

RAW

Manual focus

Normal focus range

60 cm

Macro focus range

13 cm

10 cm

Focal length (35mm equiv.)

34 - 102 mm

Aperture priority

Max. aperture

f2.7 - f5.2

f2.7 - f4.6

Max. aperture (35mm equiv.)

f16.3 - f31.3

f16.3 - f27.7

Metering

Centre weighted, Multi-pattern, Spot

Centre weighted, Multi-segment, Spot

Exposure compensation

±2 EV (in 1/2 EV steps)

Shutter priority

Min. shutter speed

1/2 sec

Max. shutter speed

1/1400 sec

Built-in flash

External flash

Viewfinder

Optical

Optical (tunnel)

White balance presets

Screen size

1.6"

Screen resolution

61,000 dots

Video capture

Max. video resolution

Storage types

MultiMedia, Secure Digital

USB

USB 1.1

USB 1.0

HDMI

Wireless

GPS

Battery

1x CR-V3, 2x AA

AA (2) batteries (NiMH recommended)

Weight

192 g

178 g

Dimensions

102.5 x 65 x 38 mm

Year

2005

2004

Choose cameras to compare

Popular comparisons:

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:

Diagonal = √

w² + h²

where w = sensor width and h = sensor height

Kodak CX7525 diagonal

The diagonal of CX7525 sensor is not 1/2.5 or 0.4" (10.2 mm) as you might expect, but approximately two thirds of that value - 7.19 mm. If you want to know why, see sensor sizes.

w = 5.75 mm
h = 4.32 mm

Diagonal = √

5.75² + 4.32²

= 7.19 mm

Kodak CX7430 diagonal

The diagonal of CX7430 sensor is not 1/2.5 or 0.4" (10.2 mm) as you might expect, but approximately two thirds of that value - 7.19 mm. If you want to know why, see sensor sizes.

w = 5.75 mm
h = 4.32 mm

Diagonal = √

5.75² + 4.32²

= 7.19 mm

Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

CX7525 sensor area

Width = 5.75 mm
Height = 4.32 mm

Surface area = 5.75 × 4.32 = 24.84 mm²

CX7430 sensor area

Width = 5.75 mm
Height = 4.32 mm

Surface area = 5.75 × 4.32 = 24.84 mm²

Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:

Pixel pitch =	sensor width in mm	× 1000
	sensor resolution width in pixels

CX7525 pixel pitch

Sensor width = 5.75 mm
Sensor resolution width = 2371 pixels

Pixel pitch =	5.75	× 1000	= 2.43 µm
	2371

CX7430 pixel pitch

Sensor width = 5.75 mm
Sensor resolution width = 2306 pixels

Pixel pitch =	5.75	× 1000	= 2.49 µm
	2306

Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:

Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:

Pixel area =	sensor surface area in mm²
	effective megapixels

CX7525 pixel area

Pixel pitch = 2.43 µm

Pixel area = 2.43² = 5.9 µm²

CX7430 pixel area

Pixel pitch = 2.49 µm

Pixel area = 2.49² = 6.2 µm²

Pixel density

Pixel density can be calculated with the following formula:

Pixel density = (	sensor resolution width in pixels	)² / 1000000
	sensor width in cm

One could also use this formula:

Pixel density =	effective megapixels × 1000000	/ 10000
	sensor surface area in mm²

CX7525 pixel density

Sensor resolution width = 2371 pixels
Sensor width = 0.575 cm

Pixel density = (2371 / 0.575)² / 1000000 = 17 MP/cm²

CX7430 pixel density

Sensor resolution width = 2306 pixels
Sensor width = 0.575 cm

Pixel density = (2306 / 0.575)² / 1000000 = 16.08 MP/cm²

Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:

(X × r) × X = effective megapixels × 1000000 →

X = √	effective megapixels × 1000000
	r

3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

CX7525 sensor resolution

Sensor width = 5.75 mm
Sensor height = 4.32 mm
Effective megapixels = 4.23

r = 5.75/4.32 = 1.33

X = √	4.23 × 1000000	= 1783
	1.33

Resolution horizontal: X × r = 1783 × 1.33 = 2371
Resolution vertical: X = 1783

Sensor resolution = 2371 x 1783

CX7430 sensor resolution

Sensor width = 5.75 mm
Sensor height = 4.32 mm
Effective megapixels = 4.00

r = 5.75/4.32 = 1.33

X = √	4.00 × 1000000	= 1734
	1.33

Resolution horizontal: X × r = 1734 × 1.33 = 2306
Resolution vertical: X = 1734

Sensor resolution = 2306 x 1734

Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.

Crop factor =	43.27 mm
	sensor diagonal in mm

CX7525 crop factor

Sensor diagonal in mm = 7.19 mm

Crop factor =	43.27	= 6.02
	7.19

CX7430 crop factor

Sensor diagonal in mm = 7.19 mm

Crop factor =	43.27	= 6.02
	7.19

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

CX7525 equivalent aperture

Crop factor = 6.02
Aperture = f2.7 - f5.2

35-mm equivalent aperture = (f2.7 - f5.2) × 6.02 = f16.3 - f31.3

CX7430 equivalent aperture

Crop factor = 6.02
Aperture = f2.7 - f4.6

35-mm equivalent aperture = (f2.7 - f4.6) × 6.02 = f16.3 - f27.7

Enter your screen size (diagonal)

My screen size is inches

Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.