Konica-Minolta DiMAGE E50 vs. Konica-Minolta DiMAGE X1
Comparison
change cameras » | |||||
|
vs |
|
|||
Konica-Minolta DiMAGE E50 | Konica-Minolta DiMAGE X1 | ||||
check price » | check price » |
Megapixels
5.00
8.30
Max. image resolution
2560 x 1920
3264 x 2448
Sensor
Sensor type
CCD
CCD
Sensor size
1/2.5" (~ 5.75 x 4.32 mm)
1/1.8" (~ 7.11 x 5.33 mm)
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera.
Sensors can vary greatly in size. As a general rule, the bigger the
sensor, the better the image quality.
Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.
Learn more about sensor sizes »
Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.
Learn more about sensor sizes »
Actual sensor size
Note: Actual size is set to screen → change »
|
vs |
|
1 | : | 1.53 |
(ratio) | ||
Konica-Minolta DiMAGE E50 | Konica-Minolta DiMAGE X1 |
Surface area:
24.84 mm² | vs | 37.90 mm² |
Difference: 13.06 mm² (53%)
DiMAGE X1 sensor is approx. 1.53x bigger than DiMAGE E50 sensor.
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.
The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Pixel or photosite area affects how much light per pixel can be gathered.
The larger it is the more light can be collected by a single pixel.
Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 0.39 µm² (9%)
A pixel on Konica-Minolta DiMAGE E50 sensor is approx. 9% bigger than a pixel on Konica-Minolta DiMAGE X1.
Pixel density tells you how many million pixels fit or would fit in one
square cm of the sensor.
Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Higher pixel density means smaller pixels and lower pixel density means larger pixels.
To learn about the accuracy of these numbers,
click here.
Specs
Konica-Minolta DiMAGE E50
Konica-Minolta DiMAGE X1
Total megapixels
Effective megapixels
Optical zoom
Yes
3x
Digital zoom
Yes
Yes
ISO sensitivity
Auto
Auto, 50, 100, 200
RAW
Manual focus
Normal focus range
50 cm
10 cm
Macro focus range
6 cm
5 cm
Focal length (35mm equiv.)
32 - 96 mm
37 - 111 mm
Aperture priority
No
No
Max. aperture
f2.8 - f4.8
f3.5 - f3.8
Metering
Centre weighted
Multi-segment, Spot
Exposure compensation
±2 EV (in 1/3 EV steps)
±2 EV (in 1/3 EV steps)
Shutter priority
No
No
Min. shutter speed
1/2 sec
1 sec
Max. shutter speed
1/1000 sec
1/1250 sec
Built-in flash
External flash
Viewfinder
Optical
None
White balance presets
5
5
Screen size
2.5"
2.5"
Screen resolution
118,000 dots
Video capture
Max. video resolution
Storage types
Secure Digital
MultiMedia, Secure Digital
USB
USB 1.1
USB 1.0
HDMI
Wireless
GPS
Battery
Li-Ion
Lithium-Ion
Weight
130 g
135 g
Dimensions
89 x 55 x 28 mm
95 x 68 x 19.5 mm
Year
2005
2005
Choose cameras to compare
Popular comparisons:
- Konica-Minolta DiMAGE E50 vs. Fujifilm FinePix Z3
- Konica-Minolta DiMAGE E50 vs. Olympus Stylus 1040
- Konica-Minolta DiMAGE E50 vs. Samsung L730
- Konica-Minolta DiMAGE E50 vs. Olympus SP 600 UZ
- Konica-Minolta DiMAGE E50 vs. Olympus E-600
- Konica-Minolta DiMAGE E50 vs. Casio Exilim EX-M2
- Konica-Minolta DiMAGE E50 vs. Olympus D-600L
- Konica-Minolta DiMAGE E50 vs. Konica-Minolta DiMAGE X1
- Konica-Minolta DiMAGE E50 vs. Samsung Digimax A6
- Konica-Minolta DiMAGE E50 vs. Samsung Digimax L60
- Konica-Minolta DiMAGE E50 vs. Samsung Digimax S600
Diagonal
Diagonal is calculated by the use of Pythagorean theorem:
where w = sensor width and h = sensor height
Diagonal = √ | w² + h² |
Konica-Minolta DiMAGE E50 diagonal
The diagonal of DiMAGE E50 sensor is not 1/2.5 or 0.4" (10.2 mm) as you might expect, but approximately two thirds of
that value - 7.19 mm. If you want to know why, see
sensor sizes.
w = 5.75 mm
h = 4.32 mm
w = 5.75 mm
h = 4.32 mm
Diagonal = √ | 5.75² + 4.32² | = 7.19 mm |
Konica-Minolta DiMAGE X1 diagonal
The diagonal of DiMAGE X1 sensor is not 1/1.8 or 0.56" (14.1 mm) as you might expect, but approximately two thirds of
that value - 8.89 mm. If you want to know why, see
sensor sizes.
w = 7.11 mm
h = 5.33 mm
w = 7.11 mm
h = 5.33 mm
Diagonal = √ | 7.11² + 5.33² | = 8.89 mm |
Surface area
Surface area is calculated by multiplying the width and the height of a sensor.
DiMAGE E50 sensor area
Width = 5.75 mm
Height = 4.32 mm
Surface area = 5.75 × 4.32 = 24.84 mm²
Height = 4.32 mm
Surface area = 5.75 × 4.32 = 24.84 mm²
DiMAGE X1 sensor area
Width = 7.11 mm
Height = 5.33 mm
Surface area = 7.11 × 5.33 = 37.90 mm²
Height = 5.33 mm
Surface area = 7.11 × 5.33 = 37.90 mm²
Pixel pitch
Pixel pitch is the distance from the center of one pixel to the center of the
next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch = | sensor width in mm | × 1000 |
sensor resolution width in pixels |
DiMAGE E50 pixel pitch
Sensor width = 5.75 mm
Sensor resolution width = 2579 pixels
Sensor resolution width = 2579 pixels
Pixel pitch = | 5.75 | × 1000 | = 2.23 µm |
2579 |
DiMAGE X1 pixel pitch
Sensor width = 7.11 mm
Sensor resolution width = 3322 pixels
Sensor resolution width = 3322 pixels
Pixel pitch = | 7.11 | × 1000 | = 2.14 µm |
3322 |
Pixel area
The area of one pixel can be calculated by simply squaring the pixel pitch:
You could also divide sensor surface area with effective megapixels:
Pixel area = pixel pitch²
You could also divide sensor surface area with effective megapixels:
Pixel area = | sensor surface area in mm² |
effective megapixels |
DiMAGE E50 pixel area
Pixel pitch = 2.23 µm
Pixel area = 2.23² = 4.97 µm²
Pixel area = 2.23² = 4.97 µm²
DiMAGE X1 pixel area
Pixel pitch = 2.14 µm
Pixel area = 2.14² = 4.58 µm²
Pixel area = 2.14² = 4.58 µm²
Pixel density
Pixel density can be calculated with the following formula:
One could also use this formula:
Pixel density = ( | sensor resolution width in pixels | )² / 1000000 |
sensor width in cm |
One could also use this formula:
Pixel density = | effective megapixels × 1000000 | / 10000 |
sensor surface area in mm² |
DiMAGE E50 pixel density
Sensor resolution width = 2579 pixels
Sensor width = 0.575 cm
Pixel density = (2579 / 0.575)² / 1000000 = 20.12 MP/cm²
Sensor width = 0.575 cm
Pixel density = (2579 / 0.575)² / 1000000 = 20.12 MP/cm²
DiMAGE X1 pixel density
Sensor resolution width = 3322 pixels
Sensor width = 0.711 cm
Pixel density = (3322 / 0.711)² / 1000000 = 21.83 MP/cm²
Sensor width = 0.711 cm
Pixel density = (3322 / 0.711)² / 1000000 = 21.83 MP/cm²
Sensor resolution
Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher
than maximum (not interpolated) image resolution which is usually stated on camera specifications.
Sensor resolution is used in pixel pitch, pixel area, and pixel density formula.
For sake of simplicity, we're going to calculate it in 3 stages.
1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.
2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
3. To get sensor resolution we then multiply X with the corresponding ratio:
Resolution horizontal: X × r
Resolution vertical: X
1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.
2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000 → |
|
Resolution horizontal: X × r
Resolution vertical: X
DiMAGE E50 sensor resolution
Sensor width = 5.75 mm
Sensor height = 4.32 mm
Effective megapixels = 5.00
Resolution horizontal: X × r = 1939 × 1.33 = 2579
Resolution vertical: X = 1939
Sensor resolution = 2579 x 1939
Sensor height = 4.32 mm
Effective megapixels = 5.00
r = 5.75/4.32 = 1.33 |
|
Resolution vertical: X = 1939
Sensor resolution = 2579 x 1939
DiMAGE X1 sensor resolution
Sensor width = 7.11 mm
Sensor height = 5.33 mm
Effective megapixels = 8.30
Resolution horizontal: X × r = 2498 × 1.33 = 3322
Resolution vertical: X = 2498
Sensor resolution = 3322 x 2498
Sensor height = 5.33 mm
Effective megapixels = 8.30
r = 7.11/5.33 = 1.33 |
|
Resolution vertical: X = 2498
Sensor resolution = 3322 x 2498
Crop factor
Crop factor or focal length multiplier is calculated by dividing the diagonal
of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor = | 43.27 mm |
sensor diagonal in mm |
DiMAGE E50 crop factor
Sensor diagonal in mm = 7.19 mm
Crop factor = | 43.27 | = 6.02 |
7.19 |
DiMAGE X1 crop factor
Sensor diagonal in mm = 8.89 mm
Crop factor = | 43.27 | = 4.87 |
8.89 |
35 mm equivalent aperture
Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture
with crop factor (a.k.a. focal length multiplier).
DiMAGE E50 equivalent aperture
Crop factor = 6.02
Aperture = f2.8 - f4.8
35-mm equivalent aperture = (f2.8 - f4.8) × 6.02 = f16.9 - f28.9
Aperture = f2.8 - f4.8
35-mm equivalent aperture = (f2.8 - f4.8) × 6.02 = f16.9 - f28.9
DiMAGE X1 equivalent aperture
Crop factor = 4.87
Aperture = f3.5 - f3.8
35-mm equivalent aperture = (f3.5 - f3.8) × 4.87 = f17 - f18.5
Aperture = f3.5 - f3.8
35-mm equivalent aperture = (f3.5 - f3.8) × 4.87 = f17 - f18.5
More comparisons of Konica-Minolta DiMAGE E50:
- Konica-Minolta DiMAGE E50 vs. Olympus Stylus 600
- Konica-Minolta DiMAGE E50 vs. Casio Exilim EX-S3
- Konica-Minolta DiMAGE E50 vs. Sigma SD9
- Konica-Minolta DiMAGE E50 vs. Canon Digital IXUS i7
- Konica-Minolta DiMAGE E50 vs. Konica-Minolta DiMAGE Xg
- Konica-Minolta DiMAGE E50 vs. Samsung Digimax i6
- Konica-Minolta DiMAGE E50 vs. Fujifilm FinePix A510
- Konica-Minolta DiMAGE E50 vs. Samsung L830
- Konica-Minolta DiMAGE E50 vs. Samsung ST500
- Konica-Minolta DiMAGE E50 vs. Fujifilm FinePix S2600hd
Enter your screen size (diagonal)
My screen size is
inches
Actual size is currently adjusted to screen.
If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.
If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.