Konica-Minolta DiMAGE E500 vs. Panasonic Lumix DMC-LS2

Comparison

change cameras »
DiMAGE E500 image
vs
Lumix DMC-LS2 image
Konica-Minolta DiMAGE E500 Panasonic Lumix DMC-LS2
check price » check price »
Megapixels
5.20
5.00
Max. image resolution
2560 x 1920
2560 x 1920

Sensor

Sensor type
CCD
CCD
Sensor size
1/2.5" (~ 5.75 x 4.32 mm)
1/2.5" (~ 5.75 x 4.32 mm)
Sensor resolution
2629 x 1977
2579 x 1939
Diagonal
7.19 mm
7.19 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1 : 1
(ratio)
Konica-Minolta DiMAGE E500 Panasonic Lumix DMC-LS2
Surface area:
24.84 mm² vs 24.84 mm²
Difference: 0 mm² (0%)
DiMAGE E500 and LS2 sensors are the same size.
Pixel pitch
2.19 µm
2.23 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 0.04 µm (2%)
Pixel pitch of LS2 is approx. 2% higher than pixel pitch of DiMAGE E500.
Pixel area
4.8 µm²
4.97 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 0.17 µm² (4%)
A pixel on Panasonic LS2 sensor is approx. 4% bigger than a pixel on Konica-Minolta DiMAGE E500.
Pixel density
20.9 MP/cm²
20.12 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 0.78 µm (4%)
Konica-Minolta DiMAGE E500 has approx. 4% higher pixel density than Panasonic LS2.
To learn about the accuracy of these numbers, click here.



Specs

Konica-Minolta DiMAGE E500
Panasonic LS2
Crop factor
6.02
6.02
Total megapixels
5.40
Effective megapixels
5.00
Optical zoom
3x
Digital zoom
Yes
Yes
ISO sensitivity
Auto, 50, 100, 200
Auto, 80, 100, 200, 400
RAW
Manual focus
Normal focus range
50 cm
50 cm
Macro focus range
6 cm
5 cm
Focal length (35mm equiv.)
32 - 96 mm
35 - 105 mm
Aperture priority
No
No
Max. aperture
f2.8 - f4.8
f2.8 - f5
Max. aperture (35mm equiv.)
f16.9 - f28.9
f16.9 - f30.1
Metering
Centre weighted, Spot
Multi-segment
Exposure compensation
±2 EV (in 1/3 EV steps)
±2 EV (in 1/3 EV steps)
Shutter priority
No
No
Min. shutter speed
2 sec
60 sec
Max. shutter speed
1/2000 sec
1/2000 sec
Built-in flash
External flash
Viewfinder
None
None
White balance presets
5
6
Screen size
2"
2"
Screen resolution
130,000 dots
86,000 dots
Video capture
Max. video resolution
Storage types
Secure Digital
Secure Digital
USB
USB 2.0 (480 Mbit/sec)
USB 1.0
HDMI
Wireless
GPS
Battery
2x AA
AA (2) batteries (NiMH recommended)
Weight
130 g
138 g
Dimensions
91 x 61 x 27 mm
110.5 x 53.5 x 30.9 mm
Year
2005
2006




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Konica-Minolta DiMAGE E500 diagonal

The diagonal of DiMAGE E500 sensor is not 1/2.5 or 0.4" (10.2 mm) as you might expect, but approximately two thirds of that value - 7.19 mm. If you want to know why, see sensor sizes.

w = 5.75 mm
h = 4.32 mm
Diagonal =  5.75² + 4.32²   = 7.19 mm

Panasonic LS2 diagonal

The diagonal of LS2 sensor is not 1/2.5 or 0.4" (10.2 mm) as you might expect, but approximately two thirds of that value - 7.19 mm. If you want to know why, see sensor sizes.

w = 5.75 mm
h = 4.32 mm
Diagonal =  5.75² + 4.32²   = 7.19 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

DiMAGE E500 sensor area

Width = 5.75 mm
Height = 4.32 mm

Surface area = 5.75 × 4.32 = 24.84 mm²

LS2 sensor area

Width = 5.75 mm
Height = 4.32 mm

Surface area = 5.75 × 4.32 = 24.84 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

DiMAGE E500 pixel pitch

Sensor width = 5.75 mm
Sensor resolution width = 2629 pixels
Pixel pitch =   5.75  × 1000  = 2.19 µm
2629

LS2 pixel pitch

Sensor width = 5.75 mm
Sensor resolution width = 2579 pixels
Pixel pitch =   5.75  × 1000  = 2.23 µm
2579


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

DiMAGE E500 pixel area

Pixel pitch = 2.19 µm

Pixel area = 2.19² = 4.8 µm²

LS2 pixel area

Pixel pitch = 2.23 µm

Pixel area = 2.23² = 4.97 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

DiMAGE E500 pixel density

Sensor resolution width = 2629 pixels
Sensor width = 0.575 cm

Pixel density = (2629 / 0.575)² / 1000000 = 20.9 MP/cm²

LS2 pixel density

Sensor resolution width = 2579 pixels
Sensor width = 0.575 cm

Pixel density = (2579 / 0.575)² / 1000000 = 20.12 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

DiMAGE E500 sensor resolution

Sensor width = 5.75 mm
Sensor height = 4.32 mm
Effective megapixels = 5.20
r = 5.75/4.32 = 1.33
X =  5.20 × 1000000  = 1977
1.33
Resolution horizontal: X × r = 1977 × 1.33 = 2629
Resolution vertical: X = 1977

Sensor resolution = 2629 x 1977

LS2 sensor resolution

Sensor width = 5.75 mm
Sensor height = 4.32 mm
Effective megapixels = 5.00
r = 5.75/4.32 = 1.33
X =  5.00 × 1000000  = 1939
1.33
Resolution horizontal: X × r = 1939 × 1.33 = 2579
Resolution vertical: X = 1939

Sensor resolution = 2579 x 1939


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


DiMAGE E500 crop factor

Sensor diagonal in mm = 7.19 mm
Crop factor =   43.27  = 6.02
7.19

LS2 crop factor

Sensor diagonal in mm = 7.19 mm
Crop factor =   43.27  = 6.02
7.19

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

DiMAGE E500 equivalent aperture

Crop factor = 6.02
Aperture = f2.8 - f4.8

35-mm equivalent aperture = (f2.8 - f4.8) × 6.02 = f16.9 - f28.9

LS2 equivalent aperture

Crop factor = 6.02
Aperture = f2.8 - f5

35-mm equivalent aperture = (f2.8 - f5) × 6.02 = f16.9 - f30.1

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.