Leica S (Type 007) vs. Leica S-E (Typ 006)

Comparison

change cameras »
S (Type 007) image
vs
S-E (Typ 006) image
Leica S (Type 007) Leica S-E (Typ 006)
check price » check price »
Megapixels
37.50
37.50
Max. image resolution
7500 x 5000
7500 x 5000

Sensor

Sensor type
CMOS
CCD
Sensor size
45 x 30 mm
45 x 30 mm
Sensor resolution
7500 x 5000
7500 x 5000
Diagonal
54.08 mm
54.08 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1 : 1
(ratio)
Leica S (Type 007) Leica S-E (Typ 006)
Surface area:
1350.00 mm² vs 1350.00 mm²
Difference: 0 mm² (0%)
S (Type 007) and S-E (Typ 006) sensors are the same size.
Pixel pitch
6 µm
6 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 0 µm (0%)
S (Type 007) and S-E (Typ 006) have the same pixel pitch.
Pixel area
36 µm²
36 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 0 µm² (0%)
Leica S (Type 007) and Leica S-E (Typ 006) have the same pixel area.
Pixel density
2.78 MP/cm²
2.78 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 0 µm (0%)
Leica S (Type 007) and Leica S-E (Typ 006) have the same pixel density.
To learn about the accuracy of these numbers, click here.



Specs

Leica S (Type 007)
Leica S-E (Typ 006)
Crop factor
0.8
0.8
Total megapixels
Effective megapixels
37.50
37.50
Optical zoom
Digital zoom
No
No
ISO sensitivity
Auto, 100, 200, 400, 800, 1600, 3200, 6400
Auto, 100, 200, 400, 800, 1600
RAW
Manual focus
Normal focus range
Macro focus range
Focal length (35mm equiv.)
Aperture priority
Yes
Yes
Max. aperture
Max. aperture (35mm equiv.)
n/a
n/a
Metering
Multi, Center-weighted, Spot
Multi, Center-weighted, Spot
Exposure compensation
±3 EV (in 1/3 EV steps)
±3 EV (in 1/3 EV steps)
Shutter priority
Yes
Yes
Min. shutter speed
125 sec
32 sec
Max. shutter speed
1/4000 sec
1/4000 sec
Built-in flash
External flash
Viewfinder
Optical (pentaprism)
Optical (pentaprism)
White balance presets
12
10
Screen size
3"
3"
Screen resolution
921,600 dots
921,600 dots
Video capture
Max. video resolution
4096x2160 (24p)
Storage types
SD/SDHC/SDXC/CompactFlash
SD/SDHC/SDXC/CompactFlash
USB
USB 3.0 (5 GBit/sec)
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
Rechargeable lithium-ion battery
Rechargeable lithium-ion battery
Weight
1260 g
1260 g
Dimensions
160 x 120 x 80 mm
160 x 120 x 80 mm
Year
2014
2014




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Leica S (Type 007) diagonal

w = 45.00 mm
h = 30.00 mm
Diagonal =  45.00² + 30.00²   = 54.08 mm

Leica S-E (Typ 006) diagonal

w = 45.00 mm
h = 30.00 mm
Diagonal =  45.00² + 30.00²   = 54.08 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

S (Type 007) sensor area

Width = 45.00 mm
Height = 30.00 mm

Surface area = 45.00 × 30.00 = 1350.00 mm²

S-E (Typ 006) sensor area

Width = 45.00 mm
Height = 30.00 mm

Surface area = 45.00 × 30.00 = 1350.00 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

S (Type 007) pixel pitch

Sensor width = 45.00 mm
Sensor resolution width = 7500 pixels
Pixel pitch =   45.00  × 1000  = 6 µm
7500

S-E (Typ 006) pixel pitch

Sensor width = 45.00 mm
Sensor resolution width = 7500 pixels
Pixel pitch =   45.00  × 1000  = 6 µm
7500


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

S (Type 007) pixel area

Pixel pitch = 6 µm

Pixel area = 6² = 36 µm²

S-E (Typ 006) pixel area

Pixel pitch = 6 µm

Pixel area = 6² = 36 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

S (Type 007) pixel density

Sensor resolution width = 7500 pixels
Sensor width = 4.5 cm

Pixel density = (7500 / 4.5)² / 1000000 = 2.78 MP/cm²

S-E (Typ 006) pixel density

Sensor resolution width = 7500 pixels
Sensor width = 4.5 cm

Pixel density = (7500 / 4.5)² / 1000000 = 2.78 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

S (Type 007) sensor resolution

Sensor width = 45.00 mm
Sensor height = 30.00 mm
Effective megapixels = 37.50
r = 45.00/30.00 = 1.5
X =  37.50 × 1000000  = 5000
1.5
Resolution horizontal: X × r = 5000 × 1.5 = 7500
Resolution vertical: X = 5000

Sensor resolution = 7500 x 5000

S-E (Typ 006) sensor resolution

Sensor width = 45.00 mm
Sensor height = 30.00 mm
Effective megapixels = 37.50
r = 45.00/30.00 = 1.5
X =  37.50 × 1000000  = 5000
1.5
Resolution horizontal: X × r = 5000 × 1.5 = 7500
Resolution vertical: X = 5000

Sensor resolution = 7500 x 5000


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


S (Type 007) crop factor

Sensor diagonal in mm = 54.08 mm
Crop factor =   43.27  = 0.8
54.08

S-E (Typ 006) crop factor

Sensor diagonal in mm = 54.08 mm
Crop factor =   43.27  = 0.8
54.08

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

S (Type 007) equivalent aperture

Aperture is a lens characteristic, so it's calculated only for fixed lens cameras. If you want to know the equivalent aperture for Leica S (Type 007), take the aperture of the lens you're using and multiply it with crop factor.

Crop factor for Leica S (Type 007) is 0.8

S-E (Typ 006) equivalent aperture

Aperture is a lens characteristic, so it's calculated only for fixed lens cameras. If you want to know the equivalent aperture for Leica S-E (Typ 006), take the aperture of the lens you're using and multiply it with crop factor.

Crop factor for Leica S-E (Typ 006) is 0.8

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.