Olympus T-110 vs. Leica X1
Comparison
| change cameras » | |||||
|
vs |
|
|||
| Olympus T-110 | Leica X1 | ||||
| check price » | check price » | ||||
Megapixels
12.00
12.20
Max. image resolution
3968 x 2976
4272 x 2856
Sensor
Sensor type
CCD
CMOS
Sensor size
1/2.3" (~ 6.16 x 4.62 mm)
23.6 x 15.8 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera.
Sensors can vary greatly in size. As a general rule, the bigger the
sensor, the better the image quality.
Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.
Learn more about sensor sizes »
Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.
Learn more about sensor sizes »
Actual sensor size
Note: Actual size is set to screen → change »
|
|
vs |
|
| 1 | : | 13.1 |
| (ratio) | ||
| Olympus T-110 | Leica X1 | |
Surface area:
| 28.46 mm² | vs | 372.88 mm² |
Difference: 344.42 mm² (1210%)
X1 sensor is approx. 13.1x bigger than T-110 sensor.
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.
The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Pixel or photosite area affects how much light per pixel can be gathered.
The larger it is the more light can be collected by a single pixel.
Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 28.32 µm² (1195%)
A pixel on Leica X1 sensor is approx. 1195% bigger than a pixel on Olympus T-110.
Pixel density tells you how many million pixels fit or would fit in one
square cm of the sensor.
Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Higher pixel density means smaller pixels and lower pixel density means larger pixels.
To learn about the accuracy of these numbers,
click here.
Specs
Olympus T-110
Leica X1
Total megapixels
13.00
Effective megapixels
12.20
Optical zoom
Yes
1x
Digital zoom
Yes
No
ISO sensitivity
Auto, 100, 200, 400, 800, 1600
Auto, 100, 200, 400, 800, 1600, 3200
RAW
Manual focus
Normal focus range
60 cm
60 cm
Macro focus range
5 cm
30 cm
Focal length (35mm equiv.)
36 - 108 mm
36 mm
Aperture priority
No
Yes
Max. aperture
f3.1 - f5.9
f2.8
Metering
ESP Digital
Multi, Center-weighted, Spot
Exposure compensation
±2 EV (in 1/3 EV steps)
±3 EV (in 1/3 EV steps)
Shutter priority
No
Yes
Min. shutter speed
4 sec
30 sec
Max. shutter speed
1/2000 sec
1/2000 sec
Built-in flash
External flash
Viewfinder
None
None
White balance presets
5
5
Screen size
2.7"
2.7"
Screen resolution
230,000 dots
230,000 dots
Video capture
Max. video resolution
Storage types
SDHC, Secure Digital
SD/SDHC
USB
USB 2.0 (480 Mbit/sec)
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
BP-DC8 Rechargeable Lithium-Ion Battery Pack
Weight
135 g
306 g
Dimensions
93 x 60 x 23 mm
124 x 60 x 32 mm
Year
2010
2009
Choose cameras to compare
Popular comparisons:
- Olympus T-110 vs. Olympus FE-230
- Olympus T-110 vs. Sony Cyber-shot DSC-S930
- Olympus T-110 vs. Leica Digilux 2
- Olympus T-110 vs. Olympus VR-340
- Olympus T-110 vs. Olympus VR-350
- Olympus T-110 vs. Olympus Mju 5000
- Olympus T-110 vs. Canon PowerShot A2200
- Olympus T-110 vs. Casio Exilim EX-ZS5
- Olympus T-110 vs. Leica D-Lux 6
- Olympus T-110 vs. Leica X1
- Olympus T-110 vs. Panasonic Lumix DMC-FH8
Diagonal
Diagonal is calculated by the use of Pythagorean theorem:
where w = sensor width and h = sensor height
| Diagonal = √ | w² + h² |
Olympus T-110 diagonal
The diagonal of T-110 sensor is not 1/2.3 or 0.43" (11 mm) as you might expect, but approximately two thirds of
that value - 7.7 mm. If you want to know why, see
sensor sizes.
w = 6.16 mm
h = 4.62 mm
w = 6.16 mm
h = 4.62 mm
| Diagonal = √ | 6.16² + 4.62² | = 7.70 mm |
Leica X1 diagonal
w = 23.60 mm
h = 15.80 mm
h = 15.80 mm
| Diagonal = √ | 23.60² + 15.80² | = 28.40 mm |
Surface area
Surface area is calculated by multiplying the width and the height of a sensor.
T-110 sensor area
Width = 6.16 mm
Height = 4.62 mm
Surface area = 6.16 × 4.62 = 28.46 mm²
Height = 4.62 mm
Surface area = 6.16 × 4.62 = 28.46 mm²
X1 sensor area
Width = 23.60 mm
Height = 15.80 mm
Surface area = 23.60 × 15.80 = 372.88 mm²
Height = 15.80 mm
Surface area = 23.60 × 15.80 = 372.88 mm²
Pixel pitch
Pixel pitch is the distance from the center of one pixel to the center of the
next measured in micrometers (µm). It can be calculated with the following formula:
| Pixel pitch = | sensor width in mm | × 1000 |
| sensor resolution width in pixels |
T-110 pixel pitch
Sensor width = 6.16 mm
Sensor resolution width = 3995 pixels
Sensor resolution width = 3995 pixels
| Pixel pitch = | 6.16 | × 1000 | = 1.54 µm |
| 3995 |
X1 pixel pitch
Sensor width = 23.60 mm
Sensor resolution width = 4263 pixels
Sensor resolution width = 4263 pixels
| Pixel pitch = | 23.60 | × 1000 | = 5.54 µm |
| 4263 |
Pixel area
The area of one pixel can be calculated by simply squaring the pixel pitch:
You could also divide sensor surface area with effective megapixels:
Pixel area = pixel pitch²
You could also divide sensor surface area with effective megapixels:
| Pixel area = | sensor surface area in mm² |
| effective megapixels |
T-110 pixel area
Pixel pitch = 1.54 µm
Pixel area = 1.54² = 2.37 µm²
Pixel area = 1.54² = 2.37 µm²
X1 pixel area
Pixel pitch = 5.54 µm
Pixel area = 5.54² = 30.69 µm²
Pixel area = 5.54² = 30.69 µm²
Pixel density
Pixel density can be calculated with the following formula:
One could also use this formula:
| Pixel density = ( | sensor resolution width in pixels | )² / 1000000 |
| sensor width in cm |
One could also use this formula:
| Pixel density = | effective megapixels × 1000000 | / 10000 |
| sensor surface area in mm² |
T-110 pixel density
Sensor resolution width = 3995 pixels
Sensor width = 0.616 cm
Pixel density = (3995 / 0.616)² / 1000000 = 42.06 MP/cm²
Sensor width = 0.616 cm
Pixel density = (3995 / 0.616)² / 1000000 = 42.06 MP/cm²
X1 pixel density
Sensor resolution width = 4263 pixels
Sensor width = 2.36 cm
Pixel density = (4263 / 2.36)² / 1000000 = 3.26 MP/cm²
Sensor width = 2.36 cm
Pixel density = (4263 / 2.36)² / 1000000 = 3.26 MP/cm²
Sensor resolution
Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher
than maximum (not interpolated) image resolution which is usually stated on camera specifications.
Sensor resolution is used in pixel pitch, pixel area, and pixel density formula.
For sake of simplicity, we're going to calculate it in 3 stages.
1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.
2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
3. To get sensor resolution we then multiply X with the corresponding ratio:
Resolution horizontal: X × r
Resolution vertical: X
1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.
2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
| (X × r) × X = effective megapixels × 1000000 → |
|
Resolution horizontal: X × r
Resolution vertical: X
T-110 sensor resolution
Sensor width = 6.16 mm
Sensor height = 4.62 mm
Effective megapixels = 12.00
Resolution horizontal: X × r = 3004 × 1.33 = 3995
Resolution vertical: X = 3004
Sensor resolution = 3995 x 3004
Sensor height = 4.62 mm
Effective megapixels = 12.00
| r = 6.16/4.62 = 1.33 |
|
Resolution vertical: X = 3004
Sensor resolution = 3995 x 3004
X1 sensor resolution
Sensor width = 23.60 mm
Sensor height = 15.80 mm
Effective megapixels = 12.20
Resolution horizontal: X × r = 2861 × 1.49 = 4263
Resolution vertical: X = 2861
Sensor resolution = 4263 x 2861
Sensor height = 15.80 mm
Effective megapixels = 12.20
| r = 23.60/15.80 = 1.49 |
|
Resolution vertical: X = 2861
Sensor resolution = 4263 x 2861
Crop factor
Crop factor or focal length multiplier is calculated by dividing the diagonal
of 35 mm film (43.27 mm) with the diagonal of the sensor.
| Crop factor = | 43.27 mm |
| sensor diagonal in mm |
T-110 crop factor
Sensor diagonal in mm = 7.70 mm
| Crop factor = | 43.27 | = 5.62 |
| 7.70 |
X1 crop factor
Sensor diagonal in mm = 28.40 mm
| Crop factor = | 43.27 | = 1.52 |
| 28.40 |
35 mm equivalent aperture
Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture
with crop factor (a.k.a. focal length multiplier).
T-110 equivalent aperture
Crop factor = 5.62
Aperture = f3.1 - f5.9
35-mm equivalent aperture = (f3.1 - f5.9) × 5.62 = f17.4 - f33.2
Aperture = f3.1 - f5.9
35-mm equivalent aperture = (f3.1 - f5.9) × 5.62 = f17.4 - f33.2
X1 equivalent aperture
Crop factor = 1.52
Aperture = f2.8
35-mm equivalent aperture = (f2.8) × 1.52 = f4.3
Aperture = f2.8
35-mm equivalent aperture = (f2.8) × 1.52 = f4.3
Enter your screen size (diagonal)
My screen size is
inches
Actual size is currently adjusted to screen.
If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.
If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.