Olympus Tough TG-620 vs. Olympus Tough TG-1 iHS

Comparison

change cameras »
Tough TG-620 image
vs
Tough TG-1 iHS image
Olympus Tough TG-620 Olympus Tough TG-1 iHS
check price » check price »
Megapixels
12.70
12.00
Max. image resolution
3968 x 2976
3968 x 2976

Sensor

Sensor type
CMOS
CMOS
Sensor size
1/2.3" (~ 6.16 x 4.62 mm)
1/2.3" (~ 6.16 x 4.62 mm)
Sensor resolution
4110 x 3090
3995 x 3004
Diagonal
7.70 mm
7.70 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1 : 1
(ratio)
Olympus Tough TG-620 Olympus Tough TG-1 iHS
Surface area:
28.46 mm² vs 28.46 mm²
Difference: 0 mm² (0%)
TG-620 and TG-1 iHS sensors are the same size.
Pixel pitch
1.5 µm
1.54 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 0.04 µm (3%)
Pixel pitch of TG-1 iHS is approx. 3% higher than pixel pitch of TG-620.
Pixel area
2.25 µm²
2.37 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 0.12 µm² (5%)
A pixel on Olympus TG-1 iHS sensor is approx. 5% bigger than a pixel on Olympus TG-620.
Pixel density
44.52 MP/cm²
42.06 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 2.46 µm (6%)
Olympus TG-620 has approx. 6% higher pixel density than Olympus TG-1 iHS.
To learn about the accuracy of these numbers, click here.



Specs

Olympus TG-620
Olympus TG-1 iHS
Crop factor
5.62
5.62
Total megapixels
Effective megapixels
12.00
Optical zoom
Yes
4x
Digital zoom
Yes
Yes
ISO sensitivity
Auto, 100, 200, 400, 800, 1600, 3200, 6400
RAW
Manual focus
Normal focus range
20 cm
60 cm
Macro focus range
3 cm
Focal length (35mm equiv.)
28 - 140 mm
25 - 100 mm
Aperture priority
No
No
Max. aperture
f3.9 - f5.9
f2.0 - f4.9
Max. aperture (35mm equiv.)
f21.9 - f33.2
f11.2 - f27.5
Metering
ESP Digital, Spot
Multi, Spot
Exposure compensation
±2 EV (in 1/3 EV steps)
±2 EV (in 1/3 EV steps)
Shutter priority
No
No
Min. shutter speed
4 sec
4 sec
Max. shutter speed
1/2000 sec
1/2000 sec
Built-in flash
External flash
Viewfinder
None
None
White balance presets
7
4
Screen size
3"
3"
Screen resolution
460,000 dots
610,000 dots
Video capture
Max. video resolution
Storage types
SDHC, SDXC, Secure Digital
USB
USB 2.0 (480 Mbit/sec)
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
Li-Ion
LI90B
Weight
167 g
230 g
Dimensions
98.4 x 65.9 x 21.9 mm
100 x 65 x 26 mm
Year
2012
2012




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Olympus TG-620 diagonal

The diagonal of TG-620 sensor is not 1/2.3 or 0.43" (11 mm) as you might expect, but approximately two thirds of that value - 7.7 mm. If you want to know why, see sensor sizes.

w = 6.16 mm
h = 4.62 mm
Diagonal =  6.16² + 4.62²   = 7.70 mm

Olympus TG-1 iHS diagonal

The diagonal of TG-1 iHS sensor is not 1/2.3 or 0.43" (11 mm) as you might expect, but approximately two thirds of that value - 7.7 mm. If you want to know why, see sensor sizes.

w = 6.16 mm
h = 4.62 mm
Diagonal =  6.16² + 4.62²   = 7.70 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

TG-620 sensor area

Width = 6.16 mm
Height = 4.62 mm

Surface area = 6.16 × 4.62 = 28.46 mm²

TG-1 iHS sensor area

Width = 6.16 mm
Height = 4.62 mm

Surface area = 6.16 × 4.62 = 28.46 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

TG-620 pixel pitch

Sensor width = 6.16 mm
Sensor resolution width = 4110 pixels
Pixel pitch =   6.16  × 1000  = 1.5 µm
4110

TG-1 iHS pixel pitch

Sensor width = 6.16 mm
Sensor resolution width = 3995 pixels
Pixel pitch =   6.16  × 1000  = 1.54 µm
3995


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

TG-620 pixel area

Pixel pitch = 1.5 µm

Pixel area = 1.5² = 2.25 µm²

TG-1 iHS pixel area

Pixel pitch = 1.54 µm

Pixel area = 1.54² = 2.37 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

TG-620 pixel density

Sensor resolution width = 4110 pixels
Sensor width = 0.616 cm

Pixel density = (4110 / 0.616)² / 1000000 = 44.52 MP/cm²

TG-1 iHS pixel density

Sensor resolution width = 3995 pixels
Sensor width = 0.616 cm

Pixel density = (3995 / 0.616)² / 1000000 = 42.06 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

TG-620 sensor resolution

Sensor width = 6.16 mm
Sensor height = 4.62 mm
Effective megapixels = 12.70
r = 6.16/4.62 = 1.33
X =  12.70 × 1000000  = 3090
1.33
Resolution horizontal: X × r = 3090 × 1.33 = 4110
Resolution vertical: X = 3090

Sensor resolution = 4110 x 3090

TG-1 iHS sensor resolution

Sensor width = 6.16 mm
Sensor height = 4.62 mm
Effective megapixels = 12.00
r = 6.16/4.62 = 1.33
X =  12.00 × 1000000  = 3004
1.33
Resolution horizontal: X × r = 3004 × 1.33 = 3995
Resolution vertical: X = 3004

Sensor resolution = 3995 x 3004


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


TG-620 crop factor

Sensor diagonal in mm = 7.70 mm
Crop factor =   43.27  = 5.62
7.70

TG-1 iHS crop factor

Sensor diagonal in mm = 7.70 mm
Crop factor =   43.27  = 5.62
7.70

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

TG-620 equivalent aperture

Crop factor = 5.62
Aperture = f3.9 - f5.9

35-mm equivalent aperture = (f3.9 - f5.9) × 5.62 = f21.9 - f33.2

TG-1 iHS equivalent aperture

Crop factor = 5.62
Aperture = f2.0 - f4.9

35-mm equivalent aperture = (f2.0 - f4.9) × 5.62 = f11.2 - f27.5

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.