Pentax K110D vs. Pentax K10D
Comparison
| change cameras » | |||||
|
vs |
|
|||
| Pentax K110D | Pentax K10D | ||||
| check price » | check price » | ||||
Megapixels
6.10
10.00
Max. image resolution
3008 x 2008
3872 x 2592
Sensor
Sensor type
CCD
CCD
Sensor size
23.7 x 15.5 mm
23.5 x 15.7 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera.
Sensors can vary greatly in size. As a general rule, the bigger the
sensor, the better the image quality.
Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.
Learn more about sensor sizes »
Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.
Learn more about sensor sizes »
Actual sensor size
Note: Actual size is set to screen → change »
|
|
vs |
|
| 1 | : | 1 |
| (ratio) | ||
| Pentax K110D | Pentax K10D | |
Surface area:
| 367.35 mm² | vs | 368.95 mm² |
Difference: 1.6 mm² (0.4%)
K10D sensor is slightly bigger than K110D sensor (only 0.4% difference).
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.
The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Pixel or photosite area affects how much light per pixel can be gathered.
The larger it is the more light can be collected by a single pixel.
Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 23.38 µm² (63%)
A pixel on Pentax K110D sensor is approx. 63% bigger than a pixel on Pentax K10D.
Pixel density tells you how many million pixels fit or would fit in one
square cm of the sensor.
Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Higher pixel density means smaller pixels and lower pixel density means larger pixels.
To learn about the accuracy of these numbers,
click here.
Specs
Pentax K110D
Pentax K10D
Total megapixels
6.31
10.80
Effective megapixels
6.10
10.00
Optical zoom
Digital zoom
No
No
ISO sensitivity
Auto, 200, 400, 800, 1600, 3200
Auto, 100, 200, 400, 800, 1600
RAW
Manual focus
Normal focus range
Macro focus range
Focal length (35mm equiv.)
Aperture priority
Yes
Yes
Max. aperture
Metering
Centre weighted, Multi-segment, Spot
Centre weighted, Multi-segment, Spot
Exposure compensation
±2 EV (in 1/2 EV steps)
±3 EV (in 1/3 EV, 1/2 EV steps)
Shutter priority
Yes
Yes
Min. shutter speed
Bulb+30 sec
Bulb+30 sec
Max. shutter speed
1/4000 sec
1/4000 sec
Built-in flash
External flash
Viewfinder
Optical (pentamirror)
Optical (pentaprism)
White balance presets
7
7
Screen size
2.5"
2.5"
Screen resolution
210,000 dots
210,000 dots
Video capture
Max. video resolution
Storage types
Secure Digital
Secure Digital
USB
USB 2.0 (480 Mbit/sec)
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
AA (4) batteries (NiMH recommended)
Lithium-Ion rechargeable
Weight
585 g
710 g
Dimensions
129.5 x 92.5 x 70 mm
141.5 x 101 x 70 mm
Year
2006
2006
Choose cameras to compare
Popular comparisons:
- Pentax K110D vs. Pentax K10D
- Pentax K110D vs. Pentax K100D Super
- Pentax K110D vs. Pentax K20D
- Pentax K110D vs. Nikon D70s
- Pentax K110D vs. Pentax K-x
- Pentax K110D vs. Pentax K200D
- Pentax K110D vs. Sony Alpha SLT-A37
- Pentax K110D vs. Panasonic Lumix DMC-SZ3
- Pentax K110D vs. Nikon D3500
- Pentax K110D vs. Sony Alpha DSLR-A300
- Pentax K110D vs. Canon EOS 20D
Diagonal
Diagonal is calculated by the use of Pythagorean theorem:
where w = sensor width and h = sensor height
| Diagonal = √ | w² + h² |
Pentax K110D diagonal
w = 23.70 mm
h = 15.50 mm
h = 15.50 mm
| Diagonal = √ | 23.70² + 15.50² | = 28.32 mm |
Pentax K10D diagonal
w = 23.50 mm
h = 15.70 mm
h = 15.70 mm
| Diagonal = √ | 23.50² + 15.70² | = 28.26 mm |
Surface area
Surface area is calculated by multiplying the width and the height of a sensor.
K110D sensor area
Width = 23.70 mm
Height = 15.50 mm
Surface area = 23.70 × 15.50 = 367.35 mm²
Height = 15.50 mm
Surface area = 23.70 × 15.50 = 367.35 mm²
K10D sensor area
Width = 23.50 mm
Height = 15.70 mm
Surface area = 23.50 × 15.70 = 368.95 mm²
Height = 15.70 mm
Surface area = 23.50 × 15.70 = 368.95 mm²
Pixel pitch
Pixel pitch is the distance from the center of one pixel to the center of the
next measured in micrometers (µm). It can be calculated with the following formula:
| Pixel pitch = | sensor width in mm | × 1000 |
| sensor resolution width in pixels |
K110D pixel pitch
Sensor width = 23.70 mm
Sensor resolution width = 3055 pixels
Sensor resolution width = 3055 pixels
| Pixel pitch = | 23.70 | × 1000 | = 7.76 µm |
| 3055 |
K10D pixel pitch
Sensor width = 23.50 mm
Sensor resolution width = 3873 pixels
Sensor resolution width = 3873 pixels
| Pixel pitch = | 23.50 | × 1000 | = 6.07 µm |
| 3873 |
Pixel area
The area of one pixel can be calculated by simply squaring the pixel pitch:
You could also divide sensor surface area with effective megapixels:
Pixel area = pixel pitch²
You could also divide sensor surface area with effective megapixels:
| Pixel area = | sensor surface area in mm² |
| effective megapixels |
K110D pixel area
Pixel pitch = 7.76 µm
Pixel area = 7.76² = 60.22 µm²
Pixel area = 7.76² = 60.22 µm²
K10D pixel area
Pixel pitch = 6.07 µm
Pixel area = 6.07² = 36.84 µm²
Pixel area = 6.07² = 36.84 µm²
Pixel density
Pixel density can be calculated with the following formula:
One could also use this formula:
| Pixel density = ( | sensor resolution width in pixels | )² / 1000000 |
| sensor width in cm |
One could also use this formula:
| Pixel density = | effective megapixels × 1000000 | / 10000 |
| sensor surface area in mm² |
K110D pixel density
Sensor resolution width = 3055 pixels
Sensor width = 2.37 cm
Pixel density = (3055 / 2.37)² / 1000000 = 1.66 MP/cm²
Sensor width = 2.37 cm
Pixel density = (3055 / 2.37)² / 1000000 = 1.66 MP/cm²
K10D pixel density
Sensor resolution width = 3873 pixels
Sensor width = 2.35 cm
Pixel density = (3873 / 2.35)² / 1000000 = 2.72 MP/cm²
Sensor width = 2.35 cm
Pixel density = (3873 / 2.35)² / 1000000 = 2.72 MP/cm²
Sensor resolution
Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher
than maximum (not interpolated) image resolution which is usually stated on camera specifications.
Sensor resolution is used in pixel pitch, pixel area, and pixel density formula.
For sake of simplicity, we're going to calculate it in 3 stages.
1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.
2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
3. To get sensor resolution we then multiply X with the corresponding ratio:
Resolution horizontal: X × r
Resolution vertical: X
1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.
2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
| (X × r) × X = effective megapixels × 1000000 → |
|
Resolution horizontal: X × r
Resolution vertical: X
K110D sensor resolution
Sensor width = 23.70 mm
Sensor height = 15.50 mm
Effective megapixels = 6.10
Resolution horizontal: X × r = 1997 × 1.53 = 3055
Resolution vertical: X = 1997
Sensor resolution = 3055 x 1997
Sensor height = 15.50 mm
Effective megapixels = 6.10
| r = 23.70/15.50 = 1.53 |
|
Resolution vertical: X = 1997
Sensor resolution = 3055 x 1997
K10D sensor resolution
Sensor width = 23.50 mm
Sensor height = 15.70 mm
Effective megapixels = 10.00
Resolution horizontal: X × r = 2582 × 1.5 = 3873
Resolution vertical: X = 2582
Sensor resolution = 3873 x 2582
Sensor height = 15.70 mm
Effective megapixels = 10.00
| r = 23.50/15.70 = 1.5 |
|
Resolution vertical: X = 2582
Sensor resolution = 3873 x 2582
Crop factor
Crop factor or focal length multiplier is calculated by dividing the diagonal
of 35 mm film (43.27 mm) with the diagonal of the sensor.
| Crop factor = | 43.27 mm |
| sensor diagonal in mm |
K110D crop factor
Sensor diagonal in mm = 28.32 mm
| Crop factor = | 43.27 | = 1.53 |
| 28.32 |
K10D crop factor
Sensor diagonal in mm = 28.26 mm
| Crop factor = | 43.27 | = 1.53 |
| 28.26 |
35 mm equivalent aperture
Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture
with crop factor (a.k.a. focal length multiplier).
K110D equivalent aperture
Aperture is a lens characteristic, so it's calculated only for
fixed lens cameras. If you want to know the equivalent aperture for
Pentax K110D, take the aperture of the lens
you're using and multiply it with crop factor.
Crop factor for Pentax K110D is 1.53
Crop factor for Pentax K110D is 1.53
K10D equivalent aperture
Aperture is a lens characteristic, so it's calculated only for
fixed lens cameras. If you want to know the equivalent aperture for
Pentax K10D, take the aperture of the lens
you're using and multiply it with crop factor.
Crop factor for Pentax K10D is 1.53
Crop factor for Pentax K10D is 1.53
Enter your screen size (diagonal)
My screen size is
inches
Actual size is currently adjusted to screen.
If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.
If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.