Samsung SH100 vs. Samsung ST95

Comparison

change cameras »
SH100 image
vs
ST95 image
Samsung SH100 Samsung ST95
check price » check price »
Megapixels
14.00
16.10
Max. image resolution
4230 x 3240
4608 x 3456

Sensor

Sensor type
CCD
CCD
Sensor size
1/2.33" (~ 6.08 x 4.56 mm)
1/2.3" (~ 6.16 x 4.62 mm)
Sensor resolution
4315 x 3244
4627 x 3479
Diagonal
7.60 mm
7.70 mm
Sensor size comparison
Sensor size is generally a good indicator of the quality of the camera. Sensors can vary greatly in size. As a general rule, the bigger the sensor, the better the image quality.

Bigger sensors are more effective because they have more surface area to capture light. An important factor when comparing digital cameras is also camera generation. Generally, newer sensors will outperform the older.

Learn more about sensor sizes »

Actual sensor size

Note: Actual size is set to screen → change »
vs
1 : 1.03
(ratio)
Samsung SH100 Samsung ST95
Surface area:
27.72 mm² vs 28.46 mm²
Difference: 0.74 mm² (3%)
ST95 sensor is slightly bigger than SH100 sensor (only 3% difference).
Pixel pitch
1.41 µm
1.33 µm
Pixel pitch tells you the distance from the center of one pixel (photosite) to the center of the next. It tells you how close the pixels are to each other.

The bigger the pixel pitch, the further apart they are and the bigger each pixel is. Bigger pixels tend to have better signal to noise ratio and greater dynamic range.
Difference: 0.08 µm (6%)
Pixel pitch of SH100 is approx. 6% higher than pixel pitch of ST95.
Pixel area
1.99 µm²
1.77 µm²
Pixel or photosite area affects how much light per pixel can be gathered. The larger it is the more light can be collected by a single pixel.

Larger pixels have the potential to collect more photons, resulting in greater dynamic range, while smaller pixels provide higher resolutions (more detail) for a given sensor size.
Relative pixel sizes:
vs
Pixel area difference: 0.22 µm² (12%)
A pixel on Samsung SH100 sensor is approx. 12% bigger than a pixel on Samsung ST95.
Pixel density
50.37 MP/cm²
56.42 MP/cm²
Pixel density tells you how many million pixels fit or would fit in one square cm of the sensor.

Higher pixel density means smaller pixels and lower pixel density means larger pixels.
Difference: 6.05 µm (12%)
Samsung ST95 has approx. 12% higher pixel density than Samsung SH100.
To learn about the accuracy of these numbers, click here.



Specs

Samsung SH100
Samsung ST95
Crop factor
5.69
5.62
Total megapixels
Effective megapixels
14.00
16.10
Optical zoom
12x
5x
Digital zoom
Yes
Yes
ISO sensitivity
Auto
Auto
RAW
Manual focus
Normal focus range
80 cm
80 cm
Macro focus range
5 cm
5 cm
Focal length (35mm equiv.)
24 - 288 mm
26 - 130 mm
Aperture priority
No
No
Max. aperture
f3.3 - f5.9
f3.3 - f5.9
Max. aperture (35mm equiv.)
f18.8 - f33.6
f18.5 - f33.2
Metering
Multi, Center-weighted, Spot
Multi, Center-weighted, Spot
Exposure compensation
±2 EV (in 1/3 EV steps)
±2 EV (in 1/3 EV steps)
Shutter priority
No
No
Min. shutter speed
8 sec
8 sec
Max. shutter speed
1/2000 sec
1/2000 sec
Built-in flash
External flash
Viewfinder
None
None
White balance presets
5
5
Screen size
3"
3"
Screen resolution
230,000 dots
460,000 dots
Video capture
Max. video resolution
Storage types
SDHC, Secure Digital
SDHC, Secure Digital
USB
USB 2.0 (480 Mbit/sec)
USB 2.0 (480 Mbit/sec)
HDMI
Wireless
GPS
Battery
Lithium-Ion BP70 rechargeable battery
Lithium-Ion BP70 rechargeable battery
Weight
174 g
121 g
Dimensions
93 x 54 x 19 mm
92 x 53 x 17 mm
Year
2011
2011




Choose cameras to compare

vs

Diagonal

Diagonal is calculated by the use of Pythagorean theorem:
Diagonal =  w² + h²
where w = sensor width and h = sensor height

Samsung SH100 diagonal

The diagonal of SH100 sensor is not 1/2.33 or 0.43" (10.9 mm) as you might expect, but approximately two thirds of that value - 7.6 mm. If you want to know why, see sensor sizes.

w = 6.08 mm
h = 4.56 mm
Diagonal =  6.08² + 4.56²   = 7.60 mm

Samsung ST95 diagonal

The diagonal of ST95 sensor is not 1/2.3 or 0.43" (11 mm) as you might expect, but approximately two thirds of that value - 7.7 mm. If you want to know why, see sensor sizes.

w = 6.16 mm
h = 4.62 mm
Diagonal =  6.16² + 4.62²   = 7.70 mm


Surface area

Surface area is calculated by multiplying the width and the height of a sensor.

SH100 sensor area

Width = 6.08 mm
Height = 4.56 mm

Surface area = 6.08 × 4.56 = 27.72 mm²

ST95 sensor area

Width = 6.16 mm
Height = 4.62 mm

Surface area = 6.16 × 4.62 = 28.46 mm²


Pixel pitch

Pixel pitch is the distance from the center of one pixel to the center of the next measured in micrometers (µm). It can be calculated with the following formula:
Pixel pitch =   sensor width in mm  × 1000
sensor resolution width in pixels

SH100 pixel pitch

Sensor width = 6.08 mm
Sensor resolution width = 4315 pixels
Pixel pitch =   6.08  × 1000  = 1.41 µm
4315

ST95 pixel pitch

Sensor width = 6.16 mm
Sensor resolution width = 4627 pixels
Pixel pitch =   6.16  × 1000  = 1.33 µm
4627


Pixel area

The area of one pixel can be calculated by simply squaring the pixel pitch:
Pixel area = pixel pitch²

You could also divide sensor surface area with effective megapixels:
Pixel area =   sensor surface area in mm²
effective megapixels

SH100 pixel area

Pixel pitch = 1.41 µm

Pixel area = 1.41² = 1.99 µm²

ST95 pixel area

Pixel pitch = 1.33 µm

Pixel area = 1.33² = 1.77 µm²


Pixel density

Pixel density can be calculated with the following formula:
Pixel density =  ( sensor resolution width in pixels )² / 1000000
sensor width in cm

One could also use this formula:
Pixel density =   effective megapixels × 1000000  / 10000
sensor surface area in mm²

SH100 pixel density

Sensor resolution width = 4315 pixels
Sensor width = 0.608 cm

Pixel density = (4315 / 0.608)² / 1000000 = 50.37 MP/cm²

ST95 pixel density

Sensor resolution width = 4627 pixels
Sensor width = 0.616 cm

Pixel density = (4627 / 0.616)² / 1000000 = 56.42 MP/cm²


Sensor resolution

Sensor resolution is calculated from sensor size and effective megapixels. It's slightly higher than maximum (not interpolated) image resolution which is usually stated on camera specifications. Sensor resolution is used in pixel pitch, pixel area, and pixel density formula. For sake of simplicity, we're going to calculate it in 3 stages.

1. First we need to find the ratio between horizontal and vertical length by dividing the former with the latter (aspect ratio). It's usually 1.33 (4:3) or 1.5 (3:2), but not always.

2. With the ratio (r) known we can calculate the X from the formula below, where X is a vertical number of pixels:
(X × r) × X = effective megapixels × 1000000    →   
X =  effective megapixels × 1000000
r
3. To get sensor resolution we then multiply X with the corresponding ratio:

Resolution horizontal: X × r
Resolution vertical: X

SH100 sensor resolution

Sensor width = 6.08 mm
Sensor height = 4.56 mm
Effective megapixels = 14.00
r = 6.08/4.56 = 1.33
X =  14.00 × 1000000  = 3244
1.33
Resolution horizontal: X × r = 3244 × 1.33 = 4315
Resolution vertical: X = 3244

Sensor resolution = 4315 x 3244

ST95 sensor resolution

Sensor width = 6.16 mm
Sensor height = 4.62 mm
Effective megapixels = 16.10
r = 6.16/4.62 = 1.33
X =  16.10 × 1000000  = 3479
1.33
Resolution horizontal: X × r = 3479 × 1.33 = 4627
Resolution vertical: X = 3479

Sensor resolution = 4627 x 3479


Crop factor

Crop factor or focal length multiplier is calculated by dividing the diagonal of 35 mm film (43.27 mm) with the diagonal of the sensor.
Crop factor =   43.27 mm
sensor diagonal in mm


SH100 crop factor

Sensor diagonal in mm = 7.60 mm
Crop factor =   43.27  = 5.69
7.60

ST95 crop factor

Sensor diagonal in mm = 7.70 mm
Crop factor =   43.27  = 5.62
7.70

35 mm equivalent aperture

Equivalent aperture (in 135 film terms) is calculated by multiplying lens aperture with crop factor (a.k.a. focal length multiplier).

SH100 equivalent aperture

Crop factor = 5.69
Aperture = f3.3 - f5.9

35-mm equivalent aperture = (f3.3 - f5.9) × 5.69 = f18.8 - f33.6

ST95 equivalent aperture

Crop factor = 5.62
Aperture = f3.3 - f5.9

35-mm equivalent aperture = (f3.3 - f5.9) × 5.62 = f18.5 - f33.2

Enter your screen size (diagonal)

My screen size is  inches



Actual size is currently adjusted to screen.

If your screen (phone, tablet, or monitor) is not in diagonal, then the actual size of a sensor won't be shown correctly.